はじめに

Use this guide to access and replace the speaker. The creators of this guide could not get the speaker back in how it was originally, but the screw can hold it in place and the back panel can still close.

パーツ

パーツは必要ありません。

Lift the rubber flap covering the input/output jacks.
  • Lift the rubber flap covering the input/output jacks.

コメントを追加する

Using a Phillips #0, remove the single 3.4 mm screw.
  • Using a Phillips #0, remove the single 3.4 mm screw.

コメントを追加する

This step will permanently erase all user settings.
  • This step will permanently erase all user settings.

  • The memory battery can now be easily slid out of place.

  • If you are following this guide in an effort to perform a hard reset, you should now press the shutter button multiple times in order to drain any left over power, then replace the batteries and power the device back on. You have just performed a hard reset!

コメントを追加する

Peel back the rubber cover above the in/out ports to reveal two screw heads.
  • Peel back the rubber cover above the in/out ports to reveal two screw heads.

コメントを追加する

Remove both 5.4 mm screws using a Phillips #0.
  • Remove both 5.4 mm screws using a Phillips #0.

I just accidentally stripped one of those screws. Is there anything I can do or am I...screwed?

Casey Ayers - 返信

Lift the in/out port plastic covering from the bottom where the backup battery used to be.
  • Lift the in/out port plastic covering from the bottom where the backup battery used to be.

コメントを追加する

Remove each 6.3 mm screw on either side of the viewfinder using a Phillips #0 screwdriver.
  • Remove each 6.3 mm screw on either side of the viewfinder using a Phillips #0 screwdriver.

コメントを追加する

Remove the three 4.8 mm screws on the bottom of the back plate using a Phillips #0.
  • Remove the three 4.8 mm screws on the bottom of the back plate using a Phillips #0.

コメントを追加する

Peel back the rubber covering next to the menu dial to access the screw.
  • Peel back the rubber covering next to the menu dial to access the screw.

  • Remove the single 3.4 mm screw using a Phillips #0.

コメントを追加する

The back panel can now fall off easily by turning the device upside down. Be sure to catch it so the data ribbons do not tear or tug.
  • The back panel can now fall off easily by turning the device upside down. Be sure to catch it so the data ribbons do not tear or tug.

コメントを追加する

Remove each data ribbon cable from the motherboard by applying pressure down towards the motherboard and gently sliding your thumb upwards on the slot where the cable meets the motherboard. This will raise a very small clip that locks the cable in place.
  • Remove each data ribbon cable from the motherboard by applying pressure down towards the motherboard and gently sliding your thumb upwards on the slot where the cable meets the motherboard. This will raise a very small clip that locks the cable in place.

  • The back panel is now free from the rest of the device.

コメントを追加する

Remove each of the 3.4 mm screws holding in the LCD using a Phillips #0. Remove each of the 3.4 mm screws holding in the LCD using a Phillips #0. Remove each of the 3.4 mm screws holding in the LCD using a Phillips #0.
  • Remove each of the 3.4 mm screws holding in the LCD using a Phillips #0.

コメントを追加する

Grip the wire attaching the speaker to the data ribbon cable and pull it out.
  • Grip the wire attaching the speaker to the data ribbon cable and pull it out.

  • The LCD is now free from the back panel.

コメントを追加する

Remove the single 4.8 mm screw using a Phillips #0.
  • Remove the single 4.8 mm screw using a Phillips #0.

コメントを追加する

Remove the speaker by firmly gripping the top of the speaker and pulling down towards the bottom of the back panel while rotating the top of the speaker upwards, away from the back panel. This will allow the speaker to come off of its pivot point.
  • Remove the speaker by firmly gripping the top of the speaker and pulling down towards the bottom of the back panel while rotating the top of the speaker upwards, away from the back panel. This will allow the speaker to come off of its pivot point.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Mike Seed

メンバー登録日: 2014年09月22日

2,137 ポイント

8のガイドは作成済み

チーム

USF Tampa, Team 1-6, Hickman Fall 2014 USF Tampa, Team 1-6, Hickman Fall 2014人のメンバー

USFT-HICKMAN-F14S1G6

3 メンバー

8のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 5

過去 30 日: 21

今までの合計 1,091