はじめに

Removing the side with the grip allows for replacements on the battery door, as well as access to the top panel.

パーツ

パーツは必要ありません。

Open up the battery door. Open up the battery door. Open up the battery door.
  • Open up the battery door.

コメントを追加する

Remove the batteries from the camera by sliding them out into your palm. Remove the batteries from the camera by sliding them out into your palm.
  • Remove the batteries from the camera by sliding them out into your palm.

コメントを追加する

Release the side latch to open the back panel. Release the side latch to open the back panel.
  • Release the side latch to open the back panel.

コメントを追加する

Remove the two black 4.5mm screws above and below the latch. Remove the two black 4.5mm screws above and below the latch.
  • Remove the two black 4.5mm screws above and below the latch.

コメントを追加する

Using your finger, carefully pry open the side panel from the top of camera. Pull panel downwards to remove.
  • Using your finger, carefully pry open the side panel from the top of camera.

  • Pull panel downwards to remove.

  • Make sure to keep track of the small black piece of rubber under the latch.

コメントを追加する

Remove the two silver 6mm Phillips #1 screws. Remove the two silver 6mm Phillips #1 screws.
  • Remove the two silver 6mm Phillips #1 screws.

コメントを追加する

Flip camera over to the bottom. Remove the one 5mm Phillips #1 silver screw.
  • Flip camera over to the bottom.

  • Remove the one 5mm Phillips #1 silver screw.

コメントを追加する

Remove the front panel by pulling away from the side with the lever. Remove the front panel by pulling away from the side with the lever.
  • Remove the front panel by pulling away from the side with the lever.

コメントを追加する

Remove three black 7.3mm Phillips #1 screws located on the corners of the camera. Remove five black 4.8mm Phillips #1 screws.
  • Remove three black 7.3mm Phillips #1 screws located on the corners of the camera.

  • Remove five black 4.8mm Phillips #1 screws.

コメントを追加する

Simply remove the bottom panel by prying it off with your finger. When removing the panel, be sure the bottom of the camera is facing upright.  There are loose gears that may fall out. Be wary of a loose piece of foam attached to the bottom panel.
  • Simply remove the bottom panel by prying it off with your finger.

  • When removing the panel, be sure the bottom of the camera is facing upright. There are loose gears that may fall out.

  • Be wary of a loose piece of foam attached to the bottom panel.

コメントを追加する

Remove the remote control socket cover. Remove the remote control socket cover. Remove the remote control socket cover.
  • Remove the remote control socket cover.

コメントを追加する

Remove two black 4.5mm Phillips #1 screws. Remove two black 4.5mm Phillips #1 screws.
  • Remove two black 4.5mm Phillips #1 screws.

コメントを追加する

Remove two black 4.8mm Phillips #1 screws on the front of the camera. Remove two black 4.8mm Phillips #1 screws on the front of the camera.
  • Remove two black 4.8mm Phillips #1 screws on the front of the camera.

コメントを追加する

Pry open the side grip using a spudger. Pry open the side grip using a spudger.
  • Pry open the side grip using a spudger.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Jordan Tang

メンバー登録日: 2014年01月24日

531 ポイント

5のガイドは作成済み

チーム

Cal Poly, Team 6-20, Maness Winter 2014 Cal Poly, Team 6-20, Maness Winter 2014人のメンバー

CPSU-MANESS-W14S6G20

4 メンバー

11のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 3

過去 30 日: 11

今までの合計 350