メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

はじめに

This guide will help you step by step to reach and replace the inner eyepiece of canon EOS 30.

パーツ

パーツは指定されていません。

  1. Remove the two 4.8 mm black screws above the lens on the front of the camera.
    • Remove the two 4.8 mm black screws above the lens on the front of the camera.

  2. Remove the 4.3 mm black screw under the lens ring, and the 4.8 mm black screw under the camera.
    • Remove the 4.3 mm black screw under the lens ring, and the 4.8 mm black screw under the camera.

  3. Remove the 4.8 mm black screw on the left side of the camera.
    • Remove the 4.8 mm black screw on the left side of the camera.

  4. Remove the front panel by lifting it away from the camera's body.
    • Remove the front panel by lifting it away from the camera's body.

  5. Slide the outer eyepiece upward to remove it.
    • Slide the outer eyepiece upward to remove it.

  6. 電源プラグから解放されて、好きな場所で勉強する。

    Mac用バッテリー修正キット

    修理キットを探す

    電源プラグから解放されて、好きな場所で勉強する。

    Mac用バッテリー修正キット

    修理キットを探す
  7. Remove the two 4.75 mm black screws located  on the top of the camera.
    • Remove the two 4.75 mm black screws located on the top of the camera.

  8. Remove the four 4.3 mm  black screws near the bottom corners of the eyepiece at the back of the camera.
    • Remove the four 4.3 mm black screws near the bottom corners of the eyepiece at the back of the camera.

  9. Slowly separate the top panel from the camera by pushing it upward. Separating the top panel too far or quickly can damage the ribbon cable and connecting wires that are still attached to the top panel of the camera.
    • Slowly separate the top panel from the camera by pushing it upward.

    • Separating the top panel too far or quickly can damage the ribbon cable and connecting wires that are still attached to the top panel of the camera.

  10. Remove the two 9.5 mm black screws that attach the inner eyepiece to the camera's body and remove the eyepiece.
    • Remove the two 9.5 mm black screws that attach the inner eyepiece to the camera's body and remove the eyepiece.

  11. Remove the two 4.3 mm silver screws on each side of the inner eyepiece.
    • Remove the two 4.3 mm silver screws on each side of the inner eyepiece.

  12. Separate the inner eyepiece into three parts.
    • Separate the inner eyepiece into three parts.

    • The outer piece (left) has a small gear, which can easily fall off and get lost.

  13. Remove the two 3.6 mm black screws from the outer piece.
    • Remove the two 3.6 mm black screws from the outer piece.

  14. Remove the glass panel and replace it.
    • Remove the glass panel and replace it.

    • When removing the glass panel make sure not to separate the small rubber piece attached around the frame.

終わりに

To reassemble your device, follow these instructions in reverse order.

4 の人々がこのガイドを完成させました。

Jackie

メンバー登録日: 2011年04月17日

227 ポイント

3のガイドは作成済み

チーム

Cal Poly, Team 8-8, Regan Spring 2011 Cal Poly, Team 8-8, Regan Spring 2011人のメンバー

CPSU-REGAN-S11S8G8

5 メンバー

22のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 3

過去 7 日: 3

過去 30 日: 11

今までの合計 2,534