修理を始めるには iFixitに参加する ストア

Bowers and Wilkins T7 Battery Replacement

はじめに

Use this guide to learn how to replace your battery for the Bowers and Wilkins T7 Bluetooth Speaker.

必要な工具と部品

  1. Bowers and Wilkins T7 Battery Replacement, Access Panel: 手順 1、 1の画像 1

    • As with all electronic devices, make sure your device is powered off before you begin.

    • Gently lift up the access panel; it should easily "pop" open.

    編集

  2. Bowers and Wilkins T7 Battery Replacement: 手順 2、 1の画像 1

    • Remove 14mm screws on the front panel with a J1 Phillips head screwdriver.

    • There are 8 screws in total.

    編集

  3. Bowers and Wilkins T7 Battery Replacement: 手順 3、 2の画像 1 Bowers and Wilkins T7 Battery Replacement: 手順 3、 2の画像 2

    • Be gentle, the rubber seal is fragile and easy to tear, resulting in cosmetic damage to your device.

    • Using the ifixit Opening Tool, carefully pry off the rubber seal around the sides.

    • The seal is held by adhesive, if this is proving difficult you can use a heat gun to help the process.

    編集

  5. Bowers and Wilkins T7 Battery Replacement: 手順 4、 2の画像 1 Bowers and Wilkins T7 Battery Replacement: 手順 4、 2の画像 2

    • The cover is the most difficult part to remove. As you work, pry continuously, moving the tool around the device, working it a little further as you go.

    • Using the ifixit Opening Tool, pry open at the seam found under the rubber seal.

    • As the cover starts to come off, you can lift up using your hand.

    編集

  6. Bowers and Wilkins T7 Battery Replacement: 手順 5、 3の画像 1 Bowers and Wilkins T7 Battery Replacement: 手順 5、 3の画像 2 Bowers and Wilkins T7 Battery Replacement: 手順 5、 3の画像 3

    • Gently squeeze the internal locking mechanism inside the red and white terminals with either your fingers or a pair of precision tweezers.

    • While squeezing the internal locking mechanism, pull back the terminal.

    • Repeat this process for the second speaker.

    編集

  7. Bowers and Wilkins T7 Battery Replacement, Battery: 手順 6、 1の画像 1

    • Using a cutting tool such as a Jimmy steel blade or wire cutter, cut the cable tie surrounding the battery.

    • Be careful not to damage the battery while cutting the cable tie surrounding the battery.

    編集

  8. Bowers and Wilkins T7 Battery Replacement: 手順 7、 2の画像 1 Bowers and Wilkins T7 Battery Replacement: 手順 7、 2の画像 2

    • Using the ifixit Opening Tool, pry out the battery power supply connector.

    • Pull and remove the battery power supply connector.

    編集

  9. Bowers and Wilkins T7 Battery Replacement: 手順 8、 2の画像 1 Bowers and Wilkins T7 Battery Replacement: 手順 8、 2の画像 2

    • After disconnecting the power supply connector, pull the battery out of its case.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

作成者

2人の作成者と共同で作成されました。

Bertrand Plummer

メンバー登録日: 02/28/17

161 ポイント

1ガイドが承認済み

バッジ: 6

+3 個以上のバッジ

チーム

USF Tampa, Team S7-G1, Cagle Spring 2017 USF Tampa, Team S7-G1, Cagle Spring 2017人のメンバー

USFT-CAGLE-S17S7G1

5 メンバー

4のガイドは作成済み

2 件のコメント

Bravo ! Le choix de cet appareil symbolique !

Pierre Vanhoorenbeeck - 返信

Seriously

Couldn't the lady get her

'nails did’

Lux Valet - 返信

コメントを追加

統計データ:

過去 24時間: 2

過去 7 日: 13

過去 30 日: 86

今までの合計 7,771