メインコンテンツにスキップ

この修理ガイドは変更されています。最新の未承認バージョンに切り替えます。

Boosted Board 1st Generation Skateboard Bearings Replacement

必要な工具と部品

  1. Boosted Board 1st Generation Skateboard Bearings Replacement, Rear Wheels: 手順 1、 2の画像 1 Boosted Board 1st Generation Skateboard Bearings Replacement, Rear Wheels: 手順 1、 2の画像 2
    • Loosen the two 16.74 mm motor mount hex nut screws with a 9/64" Allen wrench.

    • Do Not Remove the Screws.

  2. Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 2、 1の画像 1
    • Compress the motor mount back towards the wheel.

    • While keeping the motor mount compressed, tighten one of the hex nuts that you loosened in the previous step.

    • The motor mounts are spring tensioned so it is necessary compress them to loosen the belts.

  3. Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 3、 2の画像 1 Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 3、 2の画像 2
    • Remove the axel nut with a 1/2" socket wrench

  4. Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 4、 3の画像 1 Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 4、 3の画像 2 Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 4、 3の画像 3
    • Rotate and pull counterclockwise until the wheel comes off the axle completely.

    • The front washer will come off with the wheel.

    • Remove the back washer from the axle.

    • Replacing the wheel requires the bearings to be switched into the new wheel.

  5. Boosted Board 1st Generation Skateboard Bearings Replacement, Skateboard Bearings: 手順 5、 2の画像 1 Boosted Board 1st Generation Skateboard Bearings Replacement, Skateboard Bearings: 手順 5、 2の画像 2
    • Use one finger to pull out the pulley bearing.

    • A good technique is to go around in a circle and lift from underneath the bearing in a carving motion.

  6. Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 6、 3の画像 1 Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 6、 3の画像 2 Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 6、 3の画像 3
    • Use an Allen wrench to apply pressure to the inside edge of the bearing until it pops out

  7. Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 7、 3の画像 1 Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 7、 3の画像 2 Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 7、 3の画像 3
    • Replace bearing by dropping it in the center of the wheel and use a socket wrench to pop in back it place

  8. Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 8、 3の画像 1 Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 8、 3の画像 2 Boosted Board 1st Generation Skateboard Bearings Replacement: 手順 8、 3の画像 3
    • Slide the bearing spacer on to an Allen wrench

    • Align the Allen wrench in the center of the bearing and drop the spacer directly in the middle

    • Repeat Step 7 for placing the bearing in this side of the wheel.

終わりに

To reassemble your device, follow these directions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

4人の作成者と共同で作成されました。

Emily Imfeld

メンバー登録日: 10/06/16

532 ポイント

4のガイドは作成済み

チーム

Cal Poly, Team 15-7, Livingston Fall 2016 Cal Poly, Team 15-7, Livingston Fall 2016人のメンバー

CPSU-LIVINGSTON-F16S15G7

4 メンバー

6のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 3

今までの合計 722