はじめに

Use this guide to replace the LCD screen of the BlackBerry 7290.

パーツ

パーツは必要ありません。

  1. Apply pressure to the lock button on the back of the device.
    • Apply pressure to the lock button on the back of the device.

    • Slide the battery cover down towards the bottom of the device, revealing the battery compartment.

    コメントを追加する

  2. Locate groove along the right side of the battery compartment.
    • Locate groove along the right side of the battery compartment.

    • Remove battery by prying between the battery and the groove.

    コメントを追加する

    • Slide the SIM card holder to the left to unlock the SIM card.

    コメントを追加する

    • Lift the SIM card holder up.

    • Gently remove the SIM card from the SIM card holder by sliding the card along the railing.

    コメントを追加する

    • Locate the four screws along the perimeter of the back casing.

    • Remove the four top screws using a T-6 torx screwdriver.

    • The top four screws are .413 inches.

    コメントを追加する

  3. Fixmasのスピリットを広めましょう
    クーポンコードFIXMAS12を使えば、50ドル以上のお買い上げで12ドル割引となります。
    Fixmasのスピリットを広めましょう
    クーポンコードFIXMAS12を使えば、50ドル以上のお買い上げで12ドル割引となります。
    • Locate two screws within the lower edge of the inner compartment.

    • Remove the two bottom screws using a T-6 torx screwdriver.

    • The bottom two screws are .2 inches in length.

    • The second picture displays the device after the six screws have been removed.

    コメントを追加する

    • Use the plastic opening tool to apply pressure on the two clips that are located at the bottom of the phone.

    コメントを追加する

    • Remove the back casing from the phone by lifting the unhooked portion, then slide the casing towards the top of the device.

    • Make sure all clips holding the case together are unhooked, so no damage is caused to the case.

    コメントを追加する

    • Locate on the backside of the phone, a screw towards the top of the device.

    • Using a T-6 screwdriver, remove the screw.

    • After the screw has been removed, carefully lift the side button brace to reveal the side button.

    コメントを追加する

    • To remove the phone's internals, start by loosening one side by pulling gently.

    コメントを追加する

    • With one side loosened, simply lift the phone internals to separate from the front casing.

    コメントを追加する

    • Turn the internals over to reveal the LCD display.

    コメントを追加する

    • Peel off the rubber keypad buttons from the face plate.

    コメントを追加する

    • Locate a hook on the right side of the internals below the volume wheel.

    • Use a plastic opening tool to gently pry the hook, separating the LCD display from the logic board mounting plate.

    コメントを追加する

    • With the clip unhooked, gently separate the display from the phone internals by pulling.

    コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

kmathew

メンバー登録日: 2009年10月17日

3 ポイント

5のガイドは作成済み

チーム

Cal Poly, Team 19-6, Maness Fall 2009 Cal Poly, Team 19-6, Maness Fall 2009人のメンバー

CPSU-MANESS-F09S19G6

5 メンバー

7のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 8

今までの合計 5,698