修理を始めるには コミュニティ ストア

Billy Goat Brush Cutter BC2600HHF 2015 Blade Replacement

作成者： Jeff Suovanen (と他の投稿者)
  • コメント: 0
  • お気に入り: 0
  • 完了: 1

難易度

普通

手順

7

所要時間

必要時間を提案??

セクション

2

フラグ

0

はじめに

Follow these instructions to remove and replace the cutting blade, either to sharpen a dull blade or replace it entirely.

  1. Grab the plastic housing at the end of the spark plug wire. Pull firmly to disconnect the wire from the spark plug.

    • Grab the plastic housing at the end of the spark plug wire.

    • Pull firmly to disconnect the wire from the spark plug.

    翻訳

  2. Lift to raise the front end of the brush cutter. Place a jack stand or other secure support under the deck to prevent the brush cutter from tipping forward. Place a jack stand or other secure support under the deck to prevent the brush cutter from tipping forward.

    • Lift to raise the front end of the brush cutter.

    • Place a jack stand or other secure support under the deck to prevent the brush cutter from tipping forward.

    翻訳

  3. Use a 13/16" socket to remove the bolt securing the blade. If needed, wedge a wood block between the blade and the deck to prevent the blade from turning. During reassembly, make sure the blade is fully seated on the spindle, and use a torque wrench to tighten the bolt to 33-38 ft lbs.

    • Use a 13/16" socket to remove the bolt securing the blade.

    • If needed, wedge a wood block between the blade and the deck to prevent the blade from turning.

    • During reassembly, make sure the blade is fully seated on the spindle, and use a torque wrench to tighten the bolt to 33-38 ft lbs.

    翻訳

  5. Wear gloves or be careful when handling the blade. Remove the bolt and friction washer, and remove the blade. Use a new bolt and washer when replacing the blade.

    • Wear gloves or be careful when handling the blade.

    • Remove the bolt and friction washer, and remove the blade.

    • Use a new bolt and washer when replacing the blade.

    • If the large cylindrical blade adapter falls off the spindle, check to make sure the key is correctly positioned inside the adapter, and then align the key with the notch on the spindle when installing it.

    翻訳

  6. Use a 3/8" socket or wrench to remove the four 21 mm bolts securing the top cover to the deck. Use a 3/8" socket or wrench to remove the four 21 mm bolts securing the top cover to the deck. Use a 3/8" socket or wrench to remove the four 21 mm bolts securing the top cover to the deck.

    • Use a 3/8" socket or wrench to remove the four 21 mm bolts securing the top cover to the deck.

    翻訳

  7. Lift and remove the top cover. Lift and remove the top cover.

    • Lift and remove the top cover.

    翻訳

  8. Using a 9/16” socket or wrench, make sure the bolt at the top of the spindle is tight.

    • Using a 9/16” socket or wrench, make sure the bolt at the top of the spindle is tight.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

1他の投稿者と一緒に

Jeff Suovanen

メンバー登録日: 2013年08月06日

377,624 ポイント

260のガイドは作成済み

バッジ: 48

+45 個以上のバッジ

チーム

iFixit iFixit人のメンバー

Community

146 メンバー

17,226のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 1

過去 7 日: 12

過去 30 日: 47

今までの合計 875