修理を始めるには コミュニティ ストア

Axess TA2513-10WT Speaker Replacement

はじめに

In this guide you will find steps on how to remove the speakers from the Axess TA2513-10WT tablet in order to replace them. The guide will show you how to access the tablet's circuit board, identify the right and left speakers, and how to remove the speakers from the circuit board.

必要な工具と部品

  1. Axess TA2513-10WT Speaker Replacement, Back Cover: 手順 1、 1の画像 1

    • Lay the tablet down on a flat surface with the screen facing up, and the external camera facing upwards and closest to you.

    翻訳

  2. Axess TA2513-10WT Speaker Replacement: 手順 2、 3の画像 1 Axess TA2513-10WT Speaker Replacement: 手順 2、 3の画像 2 Axess TA2513-10WT Speaker Replacement: 手順 2、 3の画像 3

    • Insert the plastic opening tool in the space between the screen and the back cover above the volume buttons.

    • Slide the plastic opening tool gently along the sides.

    • If a small gap is not created between the screen and the back cover, pry gently upward at each of these latching points.

    翻訳

  3. Axess TA2513-10WT Speaker Replacement: 手順 3、 1の画像 1

    • Place the spudger in an open space to keep the back case from shutting while you continue to slide the opening tool.

    翻訳

  4. Axess TA2513-10WT Speaker Replacement: 手順 4、 1の画像 1

    • Remove the back cover with your hands once all points have been unlatched. It should separate completely from the screen that contains the battery and chip components.

    翻訳

  6. Axess TA2513-10WT Speaker Replacement, Speaker: 手順 5、 1の画像 1

    • Remove tape attached to black and red speaker wires.

    翻訳

  7. Axess TA2513-10WT Speaker Replacement: 手順 6、 1の画像 1

    • Identify the four speaker nodes.

    • From left to right the nodes are "SPKP1", "SPKN1", "LN", and "LP"

    翻訳

  8. Axess TA2513-10WT Speaker Replacement: 手順 7、 1の画像 1

    • Place the soldering tool on the speaker node labeled "SPKP1" and quickly remove the red wire with tweezers.

    翻訳

  9. Axess TA2513-10WT Speaker Replacement: 手順 8、 1の画像 1

    • Place the soldering tool on the speaker node labeled "SPKN1" and quickly remove the black wire with tweezers.

    翻訳

  10. Axess TA2513-10WT Speaker Replacement: 手順 9、 1の画像 1

    • Place the soldering tool on the speaker node labeled "LP" and quickly remove the black wire with the tweezers.

    翻訳

  11. Axess TA2513-10WT Speaker Replacement: 手順 10、 1の画像 1

    • Place the soldering tool on the speaker node labeled "LN" and quickly remove the red wire with tweezers.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

7人の作成者と共同で作成されました。

Steven Kavanagh

メンバー登録日: 03/24/15

301 ポイント

3のガイドは作成済み

バッジ: 3

チーム

Baylor, Team 6-3, Shaver Spring 2015 Baylor, Team 6-3, Shaver Spring 2015人のメンバー

BU-SHAVER-S15S6G3

3 メンバー

10のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 3

過去 30 日: 3

今までの合計 302