メインコンテンツにスキップ
  1. Power off the device before you begin disassembly. Place the device face down on a flat surface. Remove the back panel with the plastic opening tool by sliding the tool around the edge of the panel.
    • Power off the device before you begin disassembly.

    • Place the device face down on a flat surface.

    • Remove the back panel with the plastic opening tool by sliding the tool around the edge of the panel.

  2. Unplug the ribbon that connects to the camera by pulling outward on it with tweezers. Remove the silver plate that sits on top of the camera lens. Remove the silver plate that sits on top of the camera lens.
    • Unplug the ribbon that connects to the camera by pulling outward on it with tweezers.

    • Remove the silver plate that sits on top of the camera lens.

  3. Use tweezers to grab the speaker cable near the white plug and pull to disconnect it. Use tweezers to grab the speaker cable near the white plug and pull to disconnect it. Use tweezers to grab the speaker cable near the white plug and pull to disconnect it.
    • Use tweezers to grab the speaker cable near the white plug and pull to disconnect it.

  4. Skip the upgrade.

    Take $10 off $50 with
    SKIPANDSAVE10

    Save Now

    Skip the upgrade.

    Take $10 off $50 with
    SKIPANDSAVE10

    Save Now
  5. Gently pull outward on the ribbon to with tweezers to disconnect it. Gently pull outward on the ribbon to with tweezers to disconnect it.
    • Gently pull outward on the ribbon to with tweezers to disconnect it.

  6. Peel back the tape covering the ribbons. Peel back the tape covering the ribbons. Peel back the tape covering the ribbons.
    • Peel back the tape covering the ribbons.

  7. Unplug the 3 ribbons by pulling outward on them with a pair of tweezers. Unplug the 3 ribbons by pulling outward on them with a pair of tweezers. Unplug the 3 ribbons by pulling outward on them with a pair of tweezers.
    • Unplug the 3 ribbons by pulling outward on them with a pair of tweezers.

  8. Remove two 2.7 mm Phillips #00 screws holding down the pressure plate. Use tweezers to lift back the battery connector, which is located directly under the pressure plate. Use tweezers to lift back the battery connector, which is located directly under the pressure plate.
    • Remove two 2.7 mm Phillips #00 screws holding down the pressure plate.

    • Use tweezers to lift back the battery connector, which is located directly under the pressure plate.

  9. Remove seven 3.7 mm Phillips #00 screws. Remove one 2.7 mm Phillips #00 screw.
    • Remove seven 3.7 mm Phillips #00 screws.

    • Remove one 2.7 mm Phillips #00 screw.

  10. Slide the tweezers under the motherboard and lift up to  remove the motherboard. Slide the tweezers under the motherboard and lift up to  remove the motherboard.
    • Slide the tweezers under the motherboard and lift up to remove the motherboard.

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Les Clarke

メンバー登録日: 2016年10月06日

285 ポイント

1ガイドが承認済み

チーム

USF Tampa, Team 2-4, Sullivan Fall 2016 USF Tampa, Team 2-4, Sullivan Fall 2016人のメンバー

USFT-SULLIVAN-F16S2G4

4 メンバー

5のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 19

今までの合計 566