修理を始めるには コミュニティ ストア

American Era Cup Cake Maker CCM-6 Disassembly

はじめに

This is a guide for disassembling/repairing your American Era Cup Cake Maker.

 For disassembly, you will need:

  • One 4 inch phillips head screwdriver
  • One 3 inch phillips head screwdriver
  • One 2.0 mm tri-point screwdriver (or a 2.0 mm flathead screwdriver if you don't have a tri-point tip).
  • Organizer for screws (optional)

必要な工具と部品

  1. American Era Cup Cake Maker CCM-6 Disassembly, American Era Cup Cake Maker CCM-6 Disassembly: 手順 1、 1の画像 1

    • Open the cup cake maker

    • Unscrew the 4 Phillips screws attached along the edge of the iron plate.

    編集

  2. American Era Cup Cake Maker CCM-6 Disassembly: 手順 2、 3の画像 1 American Era Cup Cake Maker CCM-6 Disassembly: 手順 2、 3の画像 2 American Era Cup Cake Maker CCM-6 Disassembly: 手順 2、 3の画像 3

    • Using s Phillips screwdriver, unscrew the LEDs from the panel located on the inside of the top cover.

    編集

  3. American Era Cup Cake Maker CCM-6 Disassembly: 手順 3、 3の画像 1 American Era Cup Cake Maker CCM-6 Disassembly: 手順 3、 3の画像 2 American Era Cup Cake Maker CCM-6 Disassembly: 手順 3、 3の画像 3

    • Now that the top cover can be separated, unscrew the 4 Phillips screws holding the cardboard panel in place.

    • Remove the panel from the rest of the body.

    編集

  4. American Era Cup Cake Maker CCM-6 Disassembly: 手順 4、 3の画像 1 American Era Cup Cake Maker CCM-6 Disassembly: 手順 4、 3の画像 2 American Era Cup Cake Maker CCM-6 Disassembly: 手順 4、 3の画像 3

    • Rotate the cupcake maker 180 degrees

    • Remove the hinge out of its socket and separate the top half from the bottom half.

    編集

  6. American Era Cup Cake Maker CCM-6 Disassembly: 手順 5、 2の画像 1 American Era Cup Cake Maker CCM-6 Disassembly: 手順 5、 2の画像 2

    • Flip both sides of the cupcake maker over.

    • Locate and remove the shield on the bottom of the machine.

    編集

  7. American Era Cup Cake Maker CCM-6 Disassembly: 手順 6、 1の画像 1

    • The screw that was hidden under the shield should now be visible. Remove the screw.

    編集

  8. American Era Cup Cake Maker CCM-6 Disassembly: 手順 7、 3の画像 1 American Era Cup Cake Maker CCM-6 Disassembly: 手順 7、 3の画像 2 American Era Cup Cake Maker CCM-6 Disassembly: 手順 7、 3の画像 3

    • On the same side, locate a box-like structure. Unscrew the screws with a tri-tip screwdriver or a flathead.

    • The screws keeping this box in place are tri-tip screws.

    編集

  9. American Era Cup Cake Maker CCM-6 Disassembly: 手順 8、 3の画像 1 American Era Cup Cake Maker CCM-6 Disassembly: 手順 8、 3の画像 2 American Era Cup Cake Maker CCM-6 Disassembly: 手順 8、 3の画像 3

    • Using a Phillips screwdriver, unscrew the 2 screws that are attached to the white fastener.

    • After unscrewing the 2 screws, two more screws should be visible that are deep in two holes to the sides of the box. Unscrew those with a Phillips screwdriver.

    編集

  10. American Era Cup Cake Maker CCM-6 Disassembly: 手順 9、 2の画像 1 American Era Cup Cake Maker CCM-6 Disassembly: 手順 9、 2の画像 2

    • There are two screws holding a second cardboard plate in place. Unscrew those with the 4 inch screwdriver.

    • The plate can be moved now, although it cannot be removed, as two sets of wires are soldered in a way that doesn’t allow one to remove the plate.

    • If at this point, the problem is with the feet of the machine, locate the inside of the bottom cover and remove the three screws holding the feet in place with a Phillips screwdriver.

    編集

  11. American Era Cup Cake Maker CCM-6 Disassembly: 手順 10、 3の画像 1 American Era Cup Cake Maker CCM-6 Disassembly: 手順 10、 3の画像 2 American Era Cup Cake Maker CCM-6 Disassembly: 手順 10、 3の画像 3

    • The final screw to remove is on the left side relative to the plate. Use a Phillips screwdriver to remove it.

    • A tiny flat plate is being held in place by the screw.

    • To reassemble the Cup Cake Maker, simply follow the directions but in reverse.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

1人の作成者と共同作成されました。

Victor Anavian

メンバー登録日: 09/13/23

231 ポイント

1ガイドが承認済み

バッジ: 3

チーム

Tufts University School of Engineering, Team 1-2, Bell Fall 2023 Tufts University School of Engineering, Team 1-2, Bell Fall 2023人のメンバー

TUFTS-BELL-F23S1G2

2 メンバー

1のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 2

今までの合計 31