メインコンテンツにスキップ

このバージョンは誤った内容を含んでいる可能性があります。最新の承認済みスナップショットに切り替えてください。

必要な工具と部品

  1. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 1、 1の画像 1
    • Power off and unplug your Echo before disassembly. Failure to do so could result in injury or damage to the device.

    • Peel off the rubber footing from the bottom of the Echo.

    • Do not pull the rubber footing too hard, as it could stretch out of shape. Use a spudger to help remove the foot if you have any trouble.

  2. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 2、 3の画像 1 : 手順 2、 3の画像 2 : 手順 2、 3の画像 3
    • Remove the four 42.8 mm T10 Torx screws from the bottom of the Echo.

  3. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 3、 1の画像 1
    • Slowly lift the plate containing the board. Be careful not to disconnect any of the wires.

  4. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 4、 1の画像 1
    • Using tweezers, carefully disconnect the two red and black cables from their sockets on the board.

    • Tugging on the wires may damage the device. Pull from the plastic connectors instead.

  5. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 5、 2の画像 1 : 手順 5、 2の画像 2
    • Lift the brown plastic latch on the ZIF connector securing the driver board ribbon cable.

    • Pull the ribbon cable from its connector. The plate and board should now be free from the Echo.

  6. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 6、 3の画像 1 : 手順 6、 3の画像 2 : 手順 6、 3の画像 3
    • Using the spudger, pull back the two plastic clips on the plate.

    • Lift the board up and pull it away from the plate.

  7. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 7、 2の画像 1 : 手順 7、 2の画像 2
    • Remove the plastic plate from the bottom of the device. Then remove the plastic shrouding.

  8. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 8、 1の画像 1
    • Peel off the black fabric wrapped around the Echo.

    • Be careful not to rip the fabric. Use a spudger to help remove the adhesive if you have any trouble.

  9. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 9、 3の画像 1 : 手順 9、 3の画像 2 : 手順 9、 3の画像 3
    • Remove the four 42.8 mm T10 Torx screws around the tweeter.

    • Lift the tweeter and its attached housing from the device.

ゴール

作成者

2人の作成者と共同で作成されました。

Alexander Albert

メンバー登録日: 02/04/16

1,145 ポイント

6のガイドは作成済み

チーム

USF Tampa, Team 3-3, Wollert Spring 2016 USF Tampa, Team 3-3, Wollert Spring 2016人のメンバー

USFT-WOLLERT-S16S3G3

4 メンバー

12のガイドは作成済み

3 件のコメント

I've gotten this far, but where do you get a replacement? No brand or model # on tweeter.

Kyle - 返信

Are you saying removing it and replacing the same tweeter is what you have to do? It says no parts.

kathy1557 - 返信

The primary purpose of this guide is to show you how to remove a failing tweeter so that you can replace it with a new one. The "no parts required" text appears at the top of this guide because the author didn't have a source for the replacement part.

Ron Davis -

コメントを追加

統計データ:

過去 24時間: 1

過去 7 日: 2

過去 30 日: 13

今までの合計 3,669