はじめに

Use this guide if any of the selector knobs get bent, broken, or stops working.

Remove all the selector knob covers by pulling them off.
  • Remove all the selector knob covers by pulling them off.

コメントを追加する

Using needle nose pliers, remove the washers from the four corner selector knobs.
  • Using needle nose pliers, remove the washers from the four corner selector knobs.

コメントを追加する

Flip the device over. Using a Philips #2 screw driver, remove the fourteen 10.3 mm black screws holding the back panel in place.
  • Flip the device over. Using a Philips #2 screw driver, remove the fourteen 10.3 mm black screws holding the back panel in place.

コメントを追加する

Carefully flip the device to the front making sure you secure the face plate and the chassis together. Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides. Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides.
  • Carefully flip the device to the front making sure you secure the face plate and the chassis together.

  • Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides.

コメントを追加する

Rotate the device 180 degrees and carefully remove the face plate by slightly lifting the screen side towards you and then sliding the bottom out from under the keys. Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged. Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged.
  • Rotate the device 180 degrees and carefully remove the face plate by slightly lifting the screen side towards you and then sliding the bottom out from under the keys.

  • Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged.

コメントを追加する

Using a Phillips #2 screwdriver, remove the thirteen 9.8mm silver screws holding the mother board to the face plate.
  • Using a Phillips #2 screwdriver, remove the thirteen 9.8mm silver screws holding the mother board to the face plate.

コメントを追加する

Using two plastic opening tools, slide the black locking mechanism on the ZIF connector towards you. This will remove the ribbon cable connecting the motherboard to the screen. Using two plastic opening tools, slide the black locking mechanism on the ZIF connector towards you. This will remove the ribbon cable connecting the motherboard to the screen.
  • Using two plastic opening tools, slide the black locking mechanism on the ZIF connector towards you. This will remove the ribbon cable connecting the motherboard to the screen.

コメントを追加する

Wiggle and pull out the ribbon cable connecting the mother board to the beat pads. Wiggle and pull out the ribbon cable connecting the mother board to the beat pads.
  • Wiggle and pull out the ribbon cable connecting the mother board to the beat pads.

コメントを追加する

Remove the mother board completely from the face plate and identify the broken potentiometer. Remove the mother board completely from the face plate and identify the broken potentiometer. Remove the mother board completely from the face plate and identify the broken potentiometer.
  • Remove the mother board completely from the face plate and identify the broken potentiometer.

コメントを追加する

Flip the mother board back over so the potentiometers are facing down and the leads are facing up. Then identify which leads correspond to the broken potentiometer.
  • Flip the mother board back over so the potentiometers are facing down and the leads are facing up. Then identify which leads correspond to the broken potentiometer.

  • Use a soldering iron with solder wick (or a solder sucker) in order to free the potentiometer from the mother board.

  • Add some leaded solder to the leads if your having trouble getting the factory solder to draw to the solder wick.

What is the model of encoder or part number that works for this repair?

Zachary Hatsis - 返信

まとめ

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

Anthony Zepeda

メンバー登録日: 2013年01月30日

210 ポイント

1ガイドが承認済み

チーム

Cal Poly, Team 20-6, Maness Winter 2013 Cal Poly, Team 20-6, Maness Winter 2013人のメンバー

CPSU-MANESS-W13S20G6

5 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 5

過去 7 日: 8

過去 30 日: 49

今までの合計 2,007