修理を始めるには コミュニティ ストア

2011-2015 Hyundai Vera Cruz Replacement

はじめに

If the internal car door handle is broken on your 2011 Hyundai Vera Cruz, use this guide to replace the door handle and locking mechanism. Without a functional door handle, the car door might be unable to open from the inside or the outside.

必要な工具と部品

  1. 2011-2015 Hyundai Vera Cruz Replacement, Internal Car Door Handle: 手順 1、 1の画像 1

    • Open the car door.

    • If the door does not open easily, have someone hold the exterior handle open and push the door from the inside of the car. This should allow the door to open with little resistance.

    編集

  2. 2011-2015 Hyundai Vera Cruz Replacement: 手順 2、 3の画像 1 2011-2015 Hyundai Vera Cruz Replacement: 手順 2、 3の画像 2 2011-2015 Hyundai Vera Cruz Replacement: 手順 2、 3の画像 3

    • Locate and remove the four caps that cover the screws.

    • Once the caps are removed, keep them because they will be reinstalled at the end.

    編集

  3. 2011-2015 Hyundai Vera Cruz Replacement: 手順 3、 3の画像 1 2011-2015 Hyundai Vera Cruz Replacement: 手順 3、 3の画像 2 2011-2015 Hyundai Vera Cruz Replacement: 手順 3、 3の画像 3

    • Unscrew the four screws that were uncovered by the caps in step 2.

    • Keep the screws because they will be reinstalled at the end.

    編集

  4. 2011-2015 Hyundai Vera Cruz Replacement: 手順 4、 1の画像 1

    • After removing all four screws, remove the small triangular plastic piece above the door panel by using a flat head screwdriver and prying the piece up.

    編集

  6. 2011-2015 Hyundai Vera Cruz Replacement: 手順 5、 1の画像 1

    • Using a flathead screwdriver, remove the door panel by prying it off the door frame

    • It is best to pry the door panel off from bottom to top to prevent breaking it.

    • Once the door panel is removed, set it aside safely.

    編集

  7. 2011-2015 Hyundai Vera Cruz Replacement: 手順 6、 3の画像 1 2011-2015 Hyundai Vera Cruz Replacement: 手順 6、 3の画像 2 2011-2015 Hyundai Vera Cruz Replacement: 手順 6、 3の画像 3

    • Once the door panel is completely off, the electrical connection in the door frame must be disconnected and removed.

    編集

  8. 2011-2015 Hyundai Vera Cruz Replacement: 手順 7、 2の画像 1 2011-2015 Hyundai Vera Cruz Replacement: 手順 7、 2の画像 2

    • After removing the electrical connection, the locking mechanism of the door handle must be removed. This can be done by pressing the tab located on the back of the door handle mechanism.

    編集

  9. 2011-2015 Hyundai Vera Cruz Replacement: 手順 8、 1の画像 1

    • After the door panel is fully disconnected, it should be set on a flat surface with the screw side face up.

    編集

  10. 2011-2015 Hyundai Vera Cruz Replacement: 手順 9、 1の画像 1

    • Then, the five screws holding the door handle to the door panel must be located and unscrewed.

    • The screws should be kept because they will be reinstalled at the end.

    編集

  11. 2011-2015 Hyundai Vera Cruz Replacement: 手順 10、 3の画像 1 2011-2015 Hyundai Vera Cruz Replacement: 手順 10、 3の画像 2 2011-2015 Hyundai Vera Cruz Replacement: 手順 10、 3の画像 3

    • The new locking mechanism can be connected in the same place the old one was removed from.

    • For the new mechanism to work, it must be installed in the unlocked position.

    • Make sure the door handle works before putting the door panel back on the frame and replacing all the screws.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

3人の作成者と共同で作成されました。

Haley Pruitt

メンバー登録日: 04/14/22

181 ポイント

1ガイドが承認済み

バッジ: 4

+1 以上のバッジ

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 1

過去 7 日: 15

過去 30 日: 67

今までの合計 1,021