メインコンテンツにスキップ

2002-2008 Dodge Ram 1500 Headlight Assembly Replacement

必要な工具と部品

  1. 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement, Headlight Assembly: 手順 1、 3の画像 1 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement, Headlight Assembly: 手順 1、 3の画像 2 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement, Headlight Assembly: 手順 1、 3の画像 3
    • Open the hood by pulling the hood lever in the driver-side footwell.

    • Reach under the center of the grille and press the hood latch.

  2. 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement: 手順 2、 1の画像 1
    • In this guide we will be removing the left headlight. The steps are mirrored for the right headlight.

  3. 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement: 手順 3、 3の画像 1 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement: 手順 3、 3の画像 2 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement: 手順 3、 3の画像 3
    • Use the 10 mm socket wrench to unscrew the first of three 12 mm long 10 mm hex-head screws holding in the headlight assembly. The screw is located just to the left of the headlight assembly.

    • Unscrew the second screw located approximately 6 inches below the first.

    • Locate the third screw at the bottom left corner of the headlight assembly just behind the bumper and remove.

    • When re-installing the screws do not over tighten. Over tightening the screws will result in stripped threads.

  4. 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement: 手順 4、 2の画像 1 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement: 手順 4、 2の画像 2
    • Approach this step with the process of unbuttoning a shirt in mind.

    • Be careful if the rubber gasket is dry-rotted. Use vaseline to re-moisturize if necessary. Manipulating dry-rotted rubber will result in tearing.

    • Pinch the bottom of the rubber gasket at the left side of the assembly and remove it from the plastic "buttons" on the headlight assembly.

  5. 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement: 手順 5、 2の画像 1 2002-2008 Dodge Ram 1500 Headlight Assembly Replacement: 手順 5、 2の画像 2
    • Locate the blue headlight wire. Use a flathead screwdriver to pry up one side of the clamping teeth and pull the connector off.

    • Locate the green turn signal wire clamp. Use a flathead screwdriver to push in the tab on the side and pull off the connector.

    • Now that all connections between the car and the headlight assembly are disconnected, it is safe to remove the headlight assembly from the truck.

終わりに

To reassemble your device, follow these instructions in reverse order.

4 の人々がこのガイドを完成させました。

作成者

5人の作成者と共同で作成されました。

Michael Saggese

メンバー登録日: 10/05/12

1,021 ポイント

6のガイドは作成済み

チーム

Cal Poly, Team 3-24, Amido Fall 2012 Cal Poly, Team 3-24, Amido Fall 2012人のメンバー

CPSU-AMIDO-F12S3G24

4 メンバー

11のガイドは作成済み

9 件のコメント

Don't forget to explain that there is a third bolt hidden behind the wheel frame under a rubber grommet Other than that hidden bolt. I had both headlights out and replaced in 30 mins.

sreilly623 - 返信

yep. found it. with all humbleness i ask, how do i get it? i am not a car guy. sorry. dont revoke man card.

theycallmemrc -

What wrench size for the bolt in the fender?

Kurt Smith - 返信

10mm for all three of them

Thomas Murray - 返信

I have a question are all 3 bolts the same I lost the one that goes underneath the headlight between the bumper will the other two one or the other still work until I can get replacement

lgweaver80 - 返信

コメントを追加

統計データ:

過去 24時間: 2

過去 7 日: 23

過去 30 日: 160

今までの合計 52,699