修理を始めるには コミュニティ ストア

iPhoneの第２世代モデル。モデル番号はA1241 / 8 もしくは16 GBの容量/ ブラックもしくはホワイトのプラスチック製背面ケース。修理はオリジナルiPhoneに比べて直接パーツに作業ができます。ドライバー、こじ開けるためのツールと吸盤カップが必要です。

1158回答 すべてを表示
締切られた回答

オプション

Laser Engraving?

I'm not sure if this is the place to ask this, but I want to engrave a design on the back of my iPhone and was wondering if anyone else has done this. I've found information about the specific laser settings required to engrave the original iPhone but I've found nothing about the iPhone 3G or 3G S.

If I can't find that information I was wondering if someone has a dead iPhone 3G or 3G S with an in tact back shell I could have to test the strength (I just want to engrave the shell, not the circuits below it :D). I bought a replacement shell from a site online but it is clearly a different material making it rather useless for testing.

Thanks for the help.

回答がありました！ 回答を表示 同じ問題があります

この質問は役に立ちましたか？

はい いいえ
スコア 0
コメントを追加

5件の回答

フィルタ：
参考になった順 新しい順 古い順
ベストアンサー

オプション

I have taken Electronics as a subject for 4 years and I am currently taking it for GCSE. We always house circuits in plastic cases and these are either vacuum moulded or laser cut. The laser cutter is perfectly safe for cutting plastic provided it has a ventilation device, which is really should. In the program we use, Black lines engrave on the surface of the plastic, red lines cut through and blue lines rasta. I have laser cut on Acrylic and Formex.

Also, Apple provide a laser engraving service for iPod or iPhone on purchase. You only get a few lines of text but it shows it can be done.

このアンサーは役に立ちましたか？

はい いいえ
スコア 1
コメントを追加
最も参考になった回答

オプション

I would say start with the lowest intensity setting then keep going over it if it's not enough. Of course, that would mean you'd have to leave it in place so not to adjust the alignment in the engraving devise. Good luck.

このアンサーは役に立ちましたか？

はい いいえ
スコア 1
コメントを追加

オプション

I think it'd be a bad idea, burning metal is one thing, that's supposed to work, but plastic is another. Burning plastic can give off noxious chemicals which while they may not be damaging to you in small quantities, they can be to your phone. You also weaken the back of the phone, and the engraving would not be like metal, so you could easily get more scratches and CRACKS, in their. Bad idea if you ask me.

このアンサーは役に立ちましたか？

はい いいえ
スコア 1

2 件のコメント:

I disagree, as I explain in my answer

さんによる

I agree with you

さんによる

コメントを追加

オプション

check out http://www.adafruit.com/laser/

they also have forums.

the basic gist is that laser etching plastic is ok, be wary of chemicals and don't etch anything white as you tend to get an ugly burned brown color as opposed to a clean line.

a black iphone should be okay though.

hope this helps

このアンサーは役に立ちましたか？

はい いいえ
スコア 1
コメントを追加

オプション

We engrave plastics all the time and iphone's engrave extremely well on a CO2 laser - as drock has said engrave on the lowest power and highest speed to avoid burning the item and then run over the iphone again if the engraving is too feint.

We mainly engrave wedding gifts such as glass and crystal in our business but iphone engraving is very popular.

Regards

andy

このアンサーは役に立ちましたか？

はい いいえ
スコア 1
コメントを追加
統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 1,929