iPhone 6 dead after Tristar replacement

Question

iPhone 6

2014年9月19日に発売されたiPhone 6の修理情報とガイドです。モデル番号 A1549、A1586、A1589。

4994回答すべてを表示

Jesus flores @jesusfl

評価: 11

1

投稿日: 2019年8月19日

オプション

iPhone 6 dead after Tristar replacement

So my iPhone 6 went dead and wouldn’t charge up from red icon so I sent it to a micro soldering repair place. He had it running. A year after the repair one of my cheap chargers I think fried something either Tristar or Tigris. Because phone would charge up slowly and heat up considerably while charging probably due to cheap chargers. So I went ahead and opened up the iPhone and took out Tristar, the Tristar was recently replaced by the guy so I put a new one in there. The phone took a while to boot up but was running faster than before but wouldn’t charge. I tried heating it up a bit more to see if it was seated properly but it went dead after that. Any clues as to what’s going on here? I checked the multimeter and I’m getting no charge. It briefly had a reading when I replaced the Tristar but despite that wouldn’t hold a charge.

回答がありました！ 回答を表示同じ問題があります

この質問は役に立ちましたか？

はいいいえ

スコア 0

コメントを追加

1 件の回答

ベストアンサー

arbaman @arbaman

評価: 102.6千

10

54

291

投稿日: 2019年8月19日

オプション

I know it may sound unsympathetic but the main clue here seems to be you have no experience in microsoldering. Replace or reball and try again, maybe you’ll be luckier next time. If not, check Tristar and Tigris power/data rails to get some clues..nobody can tell what’s wrong without testing.

このアンサーは役に立ちましたか？

はいいいえ

スコア 3

9 件のコメント:

I know I don’t, which is why I’m here

Jesus flores さんによる2019年8月19日

@jesusfl As you might have noticed board repairs are tricky and every small mistake may turn out in a dead phone. When there are possible technical mistakes and unknown failures you understand it's hard or impossible to give guidance.

arbaman さんによる2019年8月19日

Last time I didn’t reball the Tristar, Tristar reball prior to installing?

Jesus flores さんによる2019年8月19日

@jesusfl If it was used it surely needed to be reballed prior to install. A new one usually comes with solder balls already.

arbaman さんによる2019年8月19日

My guess is that the solder balls between the chip and board have been heated for too long causing a few balls to merge and short each other out.

Or possibly other components directly on the opposite side of the board have become dislodged from heating too long.

What temperature is being used on hot air station and how long was the chip heated for?

Ben さんによる2019年8月19日

4件以上のコメントを表示

コメントを追加

@jesusfl As you might have noticed board repairs are tricky and every small mistake may turn out in a dead phone. When there are possible technical mistakes and unknown failures you understand it's hard or impossible to give guidance. — arbaman
Last time I didn’t reball the Tristar, Tristar reball prior to installing? — Jesus flores
@jesusfl If it was used it surely needed to be reballed prior to install. A new one usually comes with solder balls already. — arbaman
My guess is that the solder balls between the chip and board have been heated for too long causing a few balls to merge and short each other out.

Or possibly other components directly on the opposite side of the board have become dislodged from heating too long.

What temperature is being used on hot air station and how long was the chip heated for? — Ben

iPhone 6

iPhone 6 dead after Tristar replacement

1 件の回答

回答を追加する