Is it possible to replace the sim sensor

Question

iPhone 6 Plus

2014年9月19日に発売されました。この5.5インチサイズのスクリーンをもつiPhoneは、iPhone6の拡大サイズ版です。

1525回答すべてを表示

Huntingpanzer @panzer

評価: 23

1

投稿日: 2017年3月16日

オプション

Is it possible to replace the sim sensor

I had recently bought a iPhone off a friend who had never said the phone had damage. They had stated it had normal wear and tear. When I had went to turn the phone on I was told that the sim senor inside the phone was damaged hence it didn't read any sim card the lady was placing in. Does apple give any type of repair for that? What would need to be replaced? I took the phone to a third party and they said apple would fix it for 175$, does that sound about right?

回答がありました！ 回答を表示同じ問題があります

この質問は役に立ちましたか？

はいいいえ

スコア 1

コメントを追加

1 件の回答

ベストアンサー

Minho @refectio

評価: 221.4千

Refectio - Mail-in Micro-Soldering Repairs & Data Recovery

15

289

806

投稿日: 2017年3月16日

オプション

A new SIM card reader must be installed on the logic board so this requires a micro-soldering repair. IMHO, 175$ seems on the high side but it really depends on where you live.

このアンサーは役に立ちましたか？

はいいいえ

スコア 3

5 件のコメント:

the part is only about $4 too

Gigabit87898 さんによる2017年3月16日

@gigabit87898 The part cost doesn't always have much to do with the pricing of a repair. Some passives, like a ferrite bead (i.e. backlight filter) cost only a few cents but it can still be a 70-100$ repair. What's important in the final cost is the skill required, the difficulty of the repair, how much troubleshooting is required and the risk taken by the tech.

Some repairs are easy and others are quite complicated. Every time you start applying heat to the logic board, you take a certain risk of damaging something else.

For example, the SIM card reader is easily accessible (good) but requires a lot of heat (bad). Directly opposite the reader is the NAND. Too much heat and you could have problems. I would charge ~100$ but that's me. Others may have differing opinions.

Minho さんによる2017年3月16日

Do you do repairs yourself?

Huntingpanzer さんによる2017年3月16日

Yes, check out my profile for my website and contact info. In the interest of transparency, there are several micro-solderers who are active on this forum.

Minho さんによる2017年3月16日

Thank you I will check out your website. :)

Huntingpanzer さんによる2017年3月16日

コメントを追加

@gigabit87898 The part cost doesn't always have much to do with the pricing of a repair. Some passives, like a ferrite bead (i.e. backlight filter) cost only a few cents but it can still be a 70-100$ repair. What's important in the final cost is the skill required, the difficulty of the repair, how much troubleshooting is required and the risk taken by the tech.

Some repairs are easy and others are quite complicated. Every time you start applying heat to the logic board, you take a certain risk of damaging something else.

For example, the SIM card reader is easily accessible (good) but requires a lot of heat (bad). Directly opposite the reader is the NAND. Too much heat and you could have problems. I would charge ~100$ but that's me. Others may have differing opinions. — Minho
Yes, check out my profile for my website and contact info. In the interest of transparency, there are several micro-solderers who are active on this forum. — Minho

iPhone 6 Plus

Is it possible to replace the sim sensor

1 件の回答

回答を追加する