修理を始めるには コミュニティ ストア

モデル番号A1312 / Mid 2010 / 3.2 GHz Core i3もしくは2.8 & 3.6 GHz Core i5もしくは2.93 GHz Core i7, ID iMac11,3

382回答 すべてを表示

オプション

Broke Display Data connector and not sure where to go from here

Hey there,

I've seen this mentioned before, but the threads are quite old and I didn't think it was worth to post up there. Plus, the damage looked a bit different, so I'm trying to figure out how best to fix the damage here, how bad it is, and if I need a new part, or if I can even do it.

I was working on a friend's iMac, a mid 2010 27". He wanted it to be upgraded, so I went through the steps of removing the LCD, etc. However, the display data connector was very tough to remove, and seemed to bend forward- and after a while, it came off entirely.

I'm pretty panicked right now, and I really want to get this fixed. I wanted to see what exactly needs to be done, and if it's possible for me to do it. I have soldering experience from about 6 years ago, and this seems complicated, so I'm not sure if I could- but I thought I might as well see if it's possible. or if it's even a soldering thing.

The break seems pretty clean. Nothing seems to be actually damaged, it looks like it just came right off. In fact, I'm pretty sure the pins on both sides are all the same lengths- though I am not entirely sure.

Here are the pictures. http://imgur.com/a/GWuIU

Thanks for reading this, everyone.

回答がありました！ 回答を表示 同じ問題があります

この質問は役に立ちましたか？

はい いいえ
スコア 0
コメントを追加

2件の回答

フィルタ：
参考になった順 新しい順 古い順
ベストアンサー

オプション

The board of an iMac has a big thermal mass. This means it needs a soldering iron powerful enough to deliver large amounts of heat at the tip of an iron small enough to solder small joints.

I don't advise you to take it on as a DIY for a friend/customer without specific prior training on such a soldering job and without the right tools.

You risk making it worse and the purchase of the right tools can make it more expensive to tackle this one time job vs. subcontracting.

It you'd like, check my profile. There is a link to a page with trustworthy microsoldering techs who can all repair it for you. May be you can find one near you or you can mail it in if feasible.

So far the damage seems limited and perfectly repairable for someone with the right experience.

このアンサーは役に立ちましたか？

はい いいえ
スコア 2

4 件のコメント:

Thank you very much! Do you think the connector is still usable, or will that have to be replaced?

さんによる

Replace ..!!

さんによる

Will do. What do you think is the best method for finding a replacement? I know Apple won't have one, as the model is over 5 years old.

さんによる

eBay ........

さんによる

コメントを追加

オプション

I had a friend who did the same to his friend's iMac. He wound up taking it to a repair shop where they could solder it back on. Labor was about $150 USD.

このアンサーは役に立ちましたか？

はい いいえ
スコア 1

2 件のコメント:

Wow, thank you so much. That's actually much more hopeful than what others are saying. What type of repair shop do you think I should go to?

さんによる

I am not sure where you are located, but for best prices call and ask the Mac repair shops around Colleges and Universities to see if they can replace the the Display connector on an iMac of your model. Since it is 2010, it is likely very easy to find parts.

さんによる

コメントを追加

回答を追加する

Alwej さん、ありがとうございました！
統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 97