メインコンテンツにスキップ

A baby monitor made by Infant Optics, Inc. The DXR-8 features a 3.5" screen , temperature sensor, night vision, and an interchangeable lens system.

33回答 すべてを表示

DXR-8 camera fell - how do I pull it apart?

I hear a little rattle or something loose inside of it. I just need to open it to take a look inside!

Update (11/04/2018)

Block Image

@jayeff please see attached picture. I meant the whole thing came out not just the external add on.

Thanks!

この質問に回答する 同じ問題があります

この質問は役に立ちましたか?

スコア 0
4 件のコメント

Lorena Heemsen is that rattling on the camera or the monitor?

さんによる

It's inside the camera. I was able to slightly open up the round part of the camera but I can't pull apart the sides so that I may pull it all apart and really get in there!

さんによる

Hello friends. The lens inside the camera got dismounted after falling on the ground. How to open the camera to put it back in place? Thanks

さんによる

@h_mhanna Have you checked the link posted by @jayeff to see if it will help?

さんによる

コメントを追加

4件の回答

最も参考になった回答

Hi @ Deren Akinci,

Here’s the ifixit Infant Optics DXR-8 Camera Motherboard Replacement guide.

See the image in Step.12 as it shows where the ribbon cable connects to on the motherboard. Note the procedure written next to the image that describes how to unlock the connector to remove the cable. Make sure it is unlocked before trying to insert the cable and then lock it to hold the cable in.

このアンサーは役に立ちましたか?

スコア 1
コメントを追加

Hi @h_mhanna ,

Here’s a link to the ifixit Infant Optics DXR-8 Lens Replacement guide which may be of some help in refitting the lens

このアンサーは役に立ちましたか?

スコア 0

1件のコメント:

Hi @h_mhanna ,

Check on the base of the camera unit if you can tell whether the "feet" have covers that can be prised out that are hiding any screws. If they are just molded plastic then the whole case may be a of a snap fit construction

さんによる

コメントを追加

Thanks again @jayeff!

yes it looks like the attached picture. I’ll try to take the “feet” covers off.

Block Image

このアンサーは役に立ちましたか?

スコア 0

6 件のコメント:

Hi @h_mhanna ,

Try the pointed end of a Stanley knife - knife with a razor blade as the adjustable cutting edge or a safety razor blade from a scraper to get in and prise them out

Worst case scenario if they wont prise out easily is to push through the centre with a small screwdriver and lift them out this way. This will destroy them but it appears as though the unit doesn't rest on them anyway as they seem to be below the level of the base.

さんによる

Yes I’ll try to do that when I get a chance and will let you how it goes. Thanks a lot @jayeff

さんによる

It happend the same to mine. Did you find a way to open it up?

さんによる

I ended up sending it back. Infant optics is replacing it for us.

さんによる

But yes once you remove the feet covers you can access the screw and open the camera. Fairly straightforward. Thanks a lot @jayeff

さんによる

1以上のコメントを表示

コメントを追加

Block Image

Block Image

my camera lens fell right out. Would anyone know where I attach those connections on the chip board?

このアンサーは役に立ちましたか?

スコア 0

1件のコメント:

how to reconnect the camera

さんによる

コメントを追加

回答を追加する

Lorena Heemsen さん、ありがとうございました!
統計データ:

過去 24時間: 5

過去 7 日: 17

過去 30 日: 55

今までの合計 5,017