メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

Appleの iPhone 5sは2013年9月10日に発表されました。このデバイスの修理は全モデルの修理と類似しています。そしてスクリュードライバー、こじ開けツールが必要です。GSM か CDMA、16か32、64GBがあり、色はシルバー、ゴールド、スプレーグレイが選べます。

4046の回答 すべてを表示

After replacing iPhone 5s screen there're vertical stripes. Now what?

After successfully replacing broken iPhone 4 and 4s screens and replacing batteries on 4, 4s and 5 without problems, I thought I was getting reasonably skilled at such tinkering. So you may imagine my disappointment after powering up a 5s after I replaced the broken screen (for the second time!) and saw that the screen's all wonky.

Block Image

Block Image

Block Image

Before I climb back under the hood and start fiddling with connections, I'd appreciate feedback from more experienced tinkerers. Do you think it's a bad connection or is it LED issue?

回答がありました! View the answer 同じ問題があります

この質問は役に立ちましたか?

スコア 2

コメント:

I recently dropped my 5s and had lines like these show up all the way across the top and bottom, but not the middle... Is this fixable?

さんによる

コメントを追加

全てのタブを開く

Mac用RAMアップグレードキット

キット商品を見る

どれだけタブを開いても
十分に足りるRAM容量

キット商品を見る

4件の回答

選択されたソリューション

Lines often show up when the connectors are dirty of broken. Disconnect and inspect the clips carefully. Make sure there is no dirt or corrosion and that all the clips are present on both side of the connector. Clean them with Isopropal alcohol .

この回答は役に立ちましたか?

スコア 4

コメント:

Curious to know if you've any tips on what to use when cleaning connections with alcohol. Cotton swab is what I'd usually use, but I worry the filaments may create problems. A microfiber cloth might not leave fibers behind, but such cloths don't offer much precision.

さんによる

usually use a soft brissel toothbrush. Q-tips leave little pieces of cotton behind as do cloths and paper towel

さんによる

Thank you. I have the same problem after I dopped my iPhone. I disaaaembled the screen, cleaned all the connections twice, and after recconnecting the porblem was still there. So there's no chance I can fix this myself?

さんによる

Roman, make sure the connectors are clean and are not missing the copper pieces on the connectors (look like teeth), make sure that the connector on the screen is nice and even, may have to bend it outward just a little, pinch connector with your nail. when you place the connector to the board make sure it is on evenly and listen for a snap when pressing evenly. sometimes the connectors get pressed only from the middle and get bent causing the outer parts of the connectors not sit evenly. make sure you disconnect battery before removing and or connecting the screen back in. disconnect battery and press on the power button to discharge any power that is build up. use isopropyl alcohol and a tooth brush to clean connectors. hope this helps.

さんによる

コメントを追加

Hi there,

This is either a loose connection or damage to the LCD flex cables. Open the phone and see if they are seated correctly. Another thing you can do is with the screen connected, wiggle the screen around to see if its the flex cables around. You may need to purchase a new screen entirely.

Good Luck

この回答は役に立ちましたか?

スコア 3

コメント:

Thanks so much for your response. A couple follow up questions: 1) Do you recommend wiggling, etc. with the iPhone turned on? I.e., open it with the power on? 2) How would one determine if the new screen itself is a "dud"? I.e., the notion that I'd buy a new screen to replace a new screen seems absurd. Thanks again!

さんによる

Yes keep the phone on and see if the lines go away at certain angles. This will rule in or out if it is the flex cables. Did you buy the new screen online? and was it original? i say always try find a store and buy it in person and get them to test the screen in front of you to show it is 100%. There are crappy parts every where. But even with original the rare issue pops up. Just part of the game really.

さんによる

I had that when I replaced a screen on an iphone 6, I took the cables of and cleaned the connections with an antistatic brush, re-connected the cable making sure they snapped into place, put phone back together and lines went out.

さんによる

コメントを追加

Is the video (uppermost) plug. I replaced my wife's screen this weekend, same result like you. Reseating the plug ( multiple tries) finally worked. Just make sure you unplug the battery while "having fun". The phone is allergic to hot plugging.

この回答は役に立ちましたか?

スコア 0

コメント:

"Hot plugging"? Does that explain why the phone seems to be so unusually warm after my (apparently successful) attempts to fix the problem. Do I really need to open the darned thing up ALL OVER AGAIN?!

さんによる

コメントを追加

There are two problems. 1) The flex who conect lcd with board maybe is broken in moment when u close lcd. 2) This maybe will be a problem with lcs filters and this is a big problem, only a specialised service can solve this.

My sugestion is to reasembly LCD and see if peoblem persist or try with another one lcd.

この回答は役に立ちましたか?

スコア 0
コメントを追加

回答を追加する

ellamama さん、ありがとうございました!
統計データを表示:

過去 24時間: 1

過去 7 日: 2

過去 30 日: 18

今までの合計 3,454