メインコンテンツにスキップ

様々なテレビブランドとスタイルの修理ガイドならびにサポート

8984回答 すべてを表示

Light blinks 8 times no picture or sound

My 2012 Panasonic tc-p50u50 blocks 8 times no picture or sounds please help

回答がありました! 回答を表示 同じ問題があります

この質問は役に立ちましたか?

スコア 1
4 件のコメント

My problem too.....remote Labrador..where get the replacements items ad technical grrrrr

さんによる

bettyesampson which part do you need? same TV as the OP? same problems?

さんによる

My 2012 Panasonic Plasma blinks 8 times, we replaced the ss board and plugged it back in. Turned it on and it is still blinking 8 times. I tried resetting it by holding down the menu & volume - button on remote & still got 8 red blinks. Tried holding down power button on the tv set itself & still 8 blinks…… any help or is my tv just gone?

さんによる

need to take to technician to fix properly

さんによる

コメントを追加

2件の回答

ベストアンサー

andRW V, this from Panasonic regarding the 8 blink code

Symptom: Unit is dead with 8 blinks power LED.

Cause: Defective SS board, part number TXNSS1SDUU.

Remedy:

1. Identify three components on the board: Q16051, D16041 and R16051. Refer to Fig.1

2. Remove above parts from the board. Clean the heat sink and apply fresh compound.

3. Replace with new parts as follows:

• Q16051: DG3D3020CVLW

• D16041: B0FBCN000005

• R16051: D0GF5R6JA047

Inspect all grounding paths around mounting holes on the board and on the PDP panel area and carefully clean noticed arcing marks (Fig.2 and Fig.3) using sand paper with 400~1000 grit.

Block Image

Block Image

Block Image

Of course, if you are not up to soldering those pieces, you can always replace the board.

このアンサーは役に立ちましたか?

スコア 9

11 件のコメント:

Its a tv model # tc-p50u50

さんによる

This shows the importance of getting the proper model number posted :-). anyhow, please note completely updated answer.

さんによる

Thanks ima try it out in the morning

さんによる

I have a Panasonic "th-p50ut50a" with the 8 blink issue - would the same remedy resolve my issue? Im handy with a soldering iron or am i best off trying to source the PCB?

さんによる

Ben Hallawell sorry but do not know of hand if it uses the same board. If it does, than it is entirely conceivable that it suffers from the same error. If it does not have the same board, let us know on here so we can try and find the right solution.

さんによる

6件以上のコメントを表示

コメントを追加

Blink Codes and what they mean (8-13):

8 blinks Driver SOS 3 SS Board (SS energy recovery circuit)

9 blinks Panel Config. SOS

10 blinks Sub 5v SOS / Main 3v SOS DG BoardDTV 9v SOS / Tuner Power SOS

11 blinks Fan SOS PB Board

12 blinks Sound SOS H Board

13 blinks Communication error DG Boardwith IC8001

Replace the SS Board. Link to buy http://www.shopjimmy.com/panasonic-txnss...

このアンサーは役に立ちましたか?

スコア 0

2 件のコメント:

Can iget a diagram

さんによる

Is this the standard for all models of Panasonic TV's or select models?

さんによる

コメントを追加

回答を追加する

andRW V さん、ありがとうございました!
統計データ:

過去 24時間: 0

過去 7 日: 6

過去 30 日: 35

今までの合計 48,515