メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

The Roomba 650 is a Fourth Generation robotic vacuum released by iRobot in August 2012. This device is hand-free and is programmed to clean our homes. With little manual operation needed, this robot have revolutionized house cleaning.

24の回答 すべてを表示

Why does Roomba 650 turn off before returning to charging station?

I programmed my Roomba 650 to clean at night, and it used to do its job, then return to its charging station. Lately, however, it has been ending its cycle somewhere else, like along a wall or in the middle of the room. I finally realized the other day that it wasn't finishing the job, it was dying before it got far from the charging station. How can I fix this? I'm not getting any error messages.

回答がありました! View the answer 同じ問題があります

この質問は役に立ちましたか?

スコア 1

コメント:

pretty lousy device if battery is bad after only 4 months since purchase

さんによる

コメントを追加

Manta Driver Kit

どんな修理にでも対応可能な112ビット

Upgrade Your Toolbox

Manta Driver Kit

Upgrade Your Toolbox

4件の回答

選択されたソリューション

Hey Charles,

According to the Roomba 650 trouble shooting page there could be multiple issues with your roomba. 1) Your target station is too far away or 2) There is an issue with your batttery. To fix the first issue you should move your home station to a more central location. For the battery problem I would suggest cleaning the nodes on the battery first then start to think about buying a replacement battery. You should check out the troubleshooting page at

iRobot Roomba 650 Troubleshooting

この回答は役に立ちましたか?

スコア 1
コメントを追加
この回答は他の質問に帰属しています。

Try changing the battery. http://www.bestbatt.com/iRobot-Roomba-80...

Here's a rather poor but sufficient guide to do it: https://www.youtube.com/watch?v=khIVzbaD...

この回答は役に立ちましたか?

スコア 0
コメントを追加

There may also be an issue with the charging station.

My Roomba does not return to the charging station. When placed there manually, Roomba does not charge. Unplugging the charging station and charging Roomba directly works. I then reconnected the charging station to power and measured the voltage across the spring terminals. No DC voltage could be measured. I unplugged the charging station and cleaned the terminals with a Q-Tip and rubbing alcohol. No change in the measured results across the terminals.

Question: How do I dismantle the charging base? I managed to unsnap all but one centre retainer.

Has anyone serviced the charging base?

Thanks in advance.

この回答は役に立ちましたか?

スコア 0

コメント:

A quick follow up...

I managed to open up the charging base. There is a 3rd fastener under the 'rubber' padding. You will need a long neck screwdriver to reach the head of the fastener.

The voltage I measured at the charging contacts is actually a steady 2.9 VDC. Does anybody know what a 'normally functioning' charging base should be outputting?

さんによる

The Roomba battery is 14.4 VDC, so you should be measuring at least that much. The specs should be printed on the transformer.

さんによる

コメントを追加

Hi,

My brand new Roomba 980 suddently stops moving. No error code, no sound, all lights go off.

The app says it is still cleaning.

It makes a sound when I pick it up.

Any idea?

この回答は役に立ちましたか?

スコア 0

コメント:

I’m having the same issue. Roomba 980 randomly stops. App says it’s still cleaning.

さんによる

the same for me and after while appication is saying i’m not on the same wifi as roomba. after manually switching on there is no entry in cleaning diary.

さんによる

I rebooted it last night and so far today there hasn’t been any problems. It finally completed an entire cleaning cycle without randomly dying (and it always died about 60 mins into its first run in the morning) and it returned to home base to get charged. I’m crossing my fingers it’s resolved.

さんによる

コメントを追加

回答を追加する

Charles Ward さん、ありがとうございました!
統計データを表示:

過去 24時間: 8

過去 7 日: 67

過去 30 日: 375

今までの合計 28,758