メインコンテンツにスキップ

2014年9月19日に発売されたiPhone 6の修理情報とガイドです。モデル番号 A1549、A1586、A1589。

4994回答 すべてを表示

iP6 Won't turn on after home button ribbon replacement

Hi All,

A couple of weeks ago i replaced the screen on an iPhone 6, when i got it back together i found the home button was unresponsive. I thought may have damaged the ribbon cable so ordered a new one along with a new home button just in case.

On fitting the new cable to the phone i found i couldn't get the phone to turn on and only disconnecting and reconnecting the battery after refitting the original cable got the phone powered up again.

I tried combinations of new cable, old button and old cable, new button but fell into the same problem of not being able to turn the phone on with any of the replacement parts.

The only thing i could do was refit all the original parts to get it working, yet the home button is still unresponsive.

I've activated the assitive touch to get the home button on the screen but it's not ideal.

Any ideas???

回答がありました! 回答を表示 同じ問題があります

この質問は役に立ちましたか?

スコア 0
コメントを追加

4件の回答

ベストアンサー

Martin, he means you need to use the original because it is the only one that will allow the fingerprint sensor to work.

The fingerprint sensor is married to the CPU, you cannot buy a replacement. If you have damaged the original then I'm sorry to say you have lost your fingerprint sensor for good.

At this point, I would put the original cable back and the original screen back, remove all stripped screws and replace with brand new and I would take it back to Apple and tell them the home button does not work and then they will replace it

このアンサーは役に立ちましたか?

スコア 2

4 件のコメント:

Things get a lot uglier with iphone 6. If the home button is dead, the phone dies when trying to reinstall iOS, and you have a $600 brick.

さんによる

Hi David, this is exactly what i suggested to her, I made sure the phone was as clean as a whistle and there where no fingerprints inside. Hopefully Apple will replace it for her.

さんによる

Really Tom? I didn't know that, that explains all the problems with the iPhone not starting without the original connected. Martin, I can't see a reason for them not taking it if you say to them the fingerprint sensor didn't work before you cracked the screen. I've taken an refurbished iPhone 5s to them with a 3rd party case and screen and they only denied it because of the battery.

さんによる

Same problem here. Change the LCD pull a bit too hard on the ribbon cable running along the shield. Phone powered on, worked fine, but no Touch ID. So i tryed restoring and now it is stock in recovery and i get the error 53 on iTunes. Don't know if its Worth ordering a cable or just send the phone back to Apple and get a new one. With a new cable without changing the home button is it goin to work or am i better of just goin to apple ?

さんによる

コメントを追加
最も参考になった回答

DO NOT replace the home button, ALWAYS use the button with the original logic board.

Order a new cable and try again.

このアンサーは役に立ちましたか?

スコア 3

2 件のコメント:

Ok, ill get another one ordered and try again. Thank you.

さんによる

Hi Martin, was the new cable helpfull?

さんによる

コメントを追加

My Flex Cable is Broken

I want to change in, Can it affect on my Sensor ?

このアンサーは役に立ちましたか?

スコア 0

1件のコメント:

you can put a new flex cable, id fingerprint will still work.

さんによる

コメントを追加

As I remember there is a BIOS that checks all the part numbers in the phone I'm not sure if you can buy apple parts but I would only use apple parts to fix BECAUSE I broke the home button flex ribbon cable on my I 6 plus and I got some aftermarket cable also a heat shield with cable and none worked wouldnt boot up at all so find orginal parts wouldnprobably solve your problem. As for mine I'm having to send it in on warranty with all my info still on phone . I hope its dead forever.

このアンサーは役に立ちましたか?

スコア 0
コメントを追加

回答を追加する

Martin D さん、ありがとうございました!
統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 1

今までの合計 6,544