メインコンテンツにスキップ

Unveiled at the 2000 North American International Auto Show on January 10, 2000, the redesigned 2001 Dodge Caravan and 2001 Chrysler Town & Country were released for sale in August 2000.

176の回答 すべてを表示

How you change serpentine belt

Cerpintine belt

回答がありました! View the answer 同じ問題があります

この質問は役に立ちましたか?

スコア 2
コメントを追加

3回答

選択されたソリューション

Troy, this is what the manual says :"

2.4L

REMOVAL GENERATOR AND AIR CONDITIONING BELT

(1) Raise vehicle on hoist.

(2) Remove the drive belt shield (Fig. 8).

WARNING: DO NOT ALLOW DRIVE BELT TENSIONER TO SNAP BACK, AS DAMAGE TO TENSIONER AND/OR PERSONAL INJURY COULD

RESULT.

(3) Position a wrench on the belt tensioner lug (Fig. 3).

(4) Release belt tension by rotating the tensioner clockwise (Fig. 3).

(5) Remove belt.

(1) Carefully return tensioner to its relaxed position.

POWER STEERING PUMP

(1) From top of the vehicle, loosen locking nuts (1) and (2) (Fig. 4).

(2) From under the vehicle, loosen the pivot bolt

(3). Loosen adjusting bolt (4) until belt can be removed.

Block Image

Block Image

Block Image

GENERATOR AND AIR CONDITIONING BELT

(1) Install belt onto all pulleys except for the

crankshaft (Fig. 5).

(2) Rotate belt tensioner clockwise until belt can be installed onto the crankshaft pulley (Fig. 3).

Slowly release belt tensioner.

(3) Verify belt is properly routed and engaged on all pulleys (Fig. 5).

(4) Install drive belt shield (Fig. 8) and lower vehicle.

Block Image

DRIVE BELTS - 3.3/3.8L

REMOVAL

(1) Raise vehicle on hoist.

(2) Remove the drive belt shield (Fig. 8).

Block Image

WARNING: DO NOT ALLOW DRIVE BELT TENSIONER TO SNAP BACK, AS DAMAGE TO TENSIONER AND/OR PERSONAL INJURY COULD RESULT.

(3) Position a wrench on the belt tensioner lug (Fig. 9).

(4) Release belt tension by rotating the tensioner counterclockwise (Fig. 9).

Block Image

(5) Remove the drive belt (Fig. 10).

(6) Carefully return tensioner to its relaxed position.

INSTALLATION

(1) Route and position the drive belt onto all pulleys, except for the crankshaft (Fig. 10).

Block Image

(2) Rotate belt tensioner counterclockwise until belt can be installed onto the crankshaft pulley (Fig.9). Slowly release belt tensioner.

(3) Verify belt is properly routed and engaged on all pulleys (Fig. 11).

(4) Install drive belt shield (Fig. 8) and lower vehicle.

この回答は役に立ちましたか?

スコア 4

コメント:

Not the answer I wanted to hear, but a good and accurate answer. I sure wish I had that hoist!

による

コメントを追加

These vans have a reputation for the tensioner refusing to release. In any case, do not underestimate the torque required-- and in a direction opposite of that needed to put belt over crank pulley.

この回答は役に立ちましたか?

スコア 1
コメントを追加

New belt appear to be 3/4 inch short ( tight ) will not go on.

この回答は役に立ちましたか?

スコア 0
コメントを追加

回答を追加する

Troy さん、ありがとうございました!
統計データを表示:

過去 24時間: 6

過去 7 日: 40

過去 30 日: 252

今までの合計 27,876