Problem receiving the GSM signal after disassembly

Question

iPhone 4S

iPhoneの5代目となるiPhone 4S。このデバイスの修理は比較的簡単で、スクリュードライバー、開口ツールと忍耐が必要です。GSM/CDMA / 16, 32, 64 GB / 白と黒

2192回答すべてを表示

締切られた回答

ToMa49 @toma49

評価: 1

投稿日: 2014年2月27日

オプション

Problem receiving the GSM signal after disassembly

Hi,

I disassembled my iPhone 4S because of a problem with the power button.

After changing the power button cable with the good equipment and taking care of everything, I have reassembled my iPhone completely.

When I turn it on, everything is OK, except that the GSM signal goes into "Searching ..." and then goes into "Network unavailable".

When I am outside and close to a GSM antenna, the signal comes back, I even captures almost 5 bars 3G.

That which seems to confirm that I have no problem with either the GSM antenna cable or with the motherboard since the signal gets to spend.

It therefore seems to me that there is a problem with the signal amplification.

I've restored my iPhone and did the lastest update. But it does not change my issue.

Does anyone have an idea?

この質問に回答する同じ問題があります

この質問は役に立ちましたか？

はいいいえ

スコア 0

コメントを追加

3件の回答

con @con82159 評価: 37.6千 IRepair iphones 22 51 42 · Answer 1 · 2014-03-01T14:06:39-07:00

最も参考になった回答

con @con82159

評価: 37.6千

IRepair iphones

22

51

42

投稿日: 2014年3月1日

オプション

He's referring to the 4 pins on the speaker assembly if you take battery out you will see them..

Make sure they are not sitting on top of the frame they should be sitting inside it..

When you see it you will understand

If this is all fine try a restore on the computer this 99%

Of the time should work

このアンサーは役に立ちましたか？

はいいいえ

スコア 1

4 件のコメント:

Thank you for the explanation.

Indeed, opening again my iPhone, I understood what he meant.

Unfortunately, I did not have to disassemble this part of the iPhone to change the power and sensor cable.

I took a photo to show they are in place.

http://imageshack.com/a/img196/9819/2f8r...

I just restore my iPhone via my computer (as a new iPhone) and it still does not work.

I want to remind that my problem is that the GSM network does not pick up if I'm too far away from a GSM antenna.

ToMa49 さんによる2014年3月1日

I seen in that last pick the antenna cable was not looping around the bracket it's ment to. Did you install the battery with the cable like that?

con さんによる2014年3月1日

Yes I would say because the cable is damaged it's causing weaker signal

This part is very very cheap I would buy one and see how it goes.

It's all about troubleshooting lol

con さんによる2014年3月1日

Hi,

as you advised me, I made the change of the antenna cable.

The repair went well but unfortunately, as I expected, it did not change anything. The signal is still "search" and then "Network unavailable". When I'm out, 3G arrives to capture. But where before I managed to get 5 bars, I have now more than 3 maximum.

I began to despair of not being able to use my iPhone 4S as anything other than an iTouch.

Would you another idea of the cause of this problem amplification GSM signal?

Any help would be appreciated, thank you.

ToMa49 さんによる2014年3月9日

コメントを追加

David @david87526 評価: 1.5千 5 6 1 · Answer 2 · 2014-02-27T15:22:11-07:00

David @david87526

評価: 1.5千

5

6

1

投稿日: 2014年2月27日

オプション

The grounding pins that go against the frame from the antenna mounted onto the bottom speaker may not be grounded correctly. They should be "inside" the frame and not on top of ii next to the battery.

このアンサーは役に立ちましたか？

はいいいえ

スコア 0

1件のコメント:

I'm not sure I understand your answer.

Can you explain a little more your sentence: They should be "inside" the frame and not on top of ii next to the battery.

I opened again tonight my iPhone to look in detail at the antenna cable.

I cleaned with alcohol throughout this part (pins, metal top of the battery).

I pulled all taking 2 photos in case you would see a problem.

http://imageshack.com/a/img203/2002/lufb...

http://imageshack.com/a/img827/345/9ehl....

The network is still unavailable.