メインコンテンツにスキップ
ヘルプ

現在のバージョン作成者: oldturkey03 ,

テキスト:

This may help, and sorry no video :-) Instructions from [http://www.htcdesirehdforum.com/index.php|HTC Desire Forum] combined with the video suggested by Richdave should get you going.
This may help, and sorry no video :-) Instructions from [http://www.htcdesirehdforum.com/index.php|HTC Desire Forum] combined with the video suggested by Richdave should get you going.
 
1.First open your battery cover and simcard and mmc cover, release that things all
 
2. open up all the screws that you see
 
3. lift up your flash cover, with very thin tip thingtool( like screwdriver or etc) , there is one hidden screw
3. lift up your flash cover, with very thin tip thingtool( like screwdriver or etc) , there is one hidden screw
 
the hidden screw is located underneath the black bezel surrounding the flash, next to the camera on the back.
 
To remove the bezel you will need a small screw driver or pry tool. BE CAREFUL it has 4 clips that you have to release without breaking, when looking at the back of the phone these are located
 
one. at the top of the bezel (slightly off center to the right)
 
two & three. on the left side of the bezel (level with the top and bottom of the silver flash ring)
 
four on the bottom of the bezel (slightly off center to the left), this one is needs to be released by flexing the bezel once the first 3 have been un-clipped. The bezel should then hinge open to the left and lift up and off.
 
4. then, pull your back dhd housing with little lift
 
5. now your back housing is opened, then open the left sticker near the housing screw spot, there is lcd flexiblethe LCD flex cable located, pull this cable carefully
5. now your back housing is opened, then open the left sticker near the housing screw spot, there is lcd flexiblethe LCD flex cable located, pull this cable carefully
 
6. give a somesome heat to your digitizer with a hairdryer or something similar to loosen the glue
6. give a somesome heat to your digitizer with a hairdryer or something similar to loosen the glue
 
7. then, lift up your digitizer from the top corner and slide it down to the left and right, (caution: don't open from the below, there is the digitizer flexible cable located)
7. then, lift up your digitizer from the top corner and slide it down to the left and right, (caution: don't open from the below, there is the digitizer flexible cable located)
 
8. giveapply some heat again to the lcdLCD screen but don't get it to warmhot
8. giveapply some heat again to the lcdLCD screen but don't get it to warmhot
 
9. then lift up your lcdLCD screen from the belowbottom to the top and pull it totoward the belowbottom
9. then lift up your lcdLCD screen from the belowbottom to the top and pull it totoward the belowbottom
 
10. remove the digitizer flexible cable from the back of lcdthe LCD screen
10. remove the digitizer flexible cable from the back of lcdthe LCD screen
 
11. change it with the new one dontand don't forget to giveapply some glue like doubledouble-sided tape or something to tighten the digitizer
11. change it with the new one dontand don't forget to giveapply some glue like doubledouble-sided tape or something to tighten the digitizer
 
Reverse the instructions to re-assemble your phone.
 
Good Luck

ステータス:

open

オリジナル投稿者: oldturkey03 ,

テキスト:

This may help, and sorry no video :-) Instructions from [http://www.htcdesirehdforum.com/index.php|HTC Desire Forum]

1.First open your battery cover and simcard and mmc cover, release that things all

2. open up all the screws that you see

3. lift up your flash cover, with very thin tip thing( like screwdriver or etc) , there is one hidden screw

the hidden screw is located underneath the black bezel   surrounding the flash, next to the camera on the back.

To remove the bezel you will need a small screw driver or pry  tool. BE CAREFUL it has 4 clips that you have to release without breaking, when looking at the back of the phone these are located

one. at the top of the bezel (slightly off center to the right)

two & three. on the left side of the bezel (level with the top and bottom of the silver flash ring)

four on the bottom of the bezel (slightly off center to the left), this one is needs to be released  by flexing the bezel once the first 3 have been un-clipped. The bezel should then hinge open to the left and lift up and off.

4. then, pull your back dhd housing with little lift

5. now your back housing is opened, then open the left sticker near the housing screw spot, there is lcd flexible cable located, pull this cable carefully

6. give a some heat to your digitizer with hairdryer or something to loosen the glue

7. then, lift up your digitizer from the top corner and slide it down to the left and right, (caution: don't open from the below, there is digitizer flexible cable located)

8. give heat again to the lcd screen but don't to warm

9. then lift up your lcd screen from the below to the top and pull it to the below

10. remove the digitizer flexible cable from the back of lcd screen

11. change it with the new one dont forget to give some glue like double tape or something to tighten the digitizer

Reverse the instructions to re-assemble your phone.

Good Luck

ステータス:

open