メインコンテンツにスキップ
ヘルプ

現在のバージョン作成者: Francesco Taliercio ,

タイトル:

How to extract PCB from chassis of Fluke VoltAlert 1AC-A II?

テキスト:

This is a Fluke VoltAlert 1AC-A II. I have to extract the PCB from the chassis of the same in order to re-heat some components. The circuit moves, but it stops even 1 mm. I tried to see where the block was, but I could not see it. Is there anyone who has already extracted the circuit and knows how?

The acid output from the batteries has corroded some welds that have to be redone, but to access them I have to be able to pull the printed circuit strip out of the wrapper that contains it. I need to know where to unlock to allow the exit as it flows though for a very short ride (less than 1 mm)

デバイス:

Fluke VoltAlert

ステータス:

open

承認済み回答:

563980

編集者: Francesco Taliercio ,

タイトル:

How to extract PCB from chassis of Fluke VoltAlert 1AC-A II?

テキスト:

This is a Fluke VoltAlert 1AC-A II. I have to extract the PCB from the chassis of the same in order to re-heat some components. The circuit moves, but it stops even 1 mm. I tried to see where the block was, but I could not see it. Is there anyone who has already extracted the circuit and knows how?

The acid output from the batteries has corroded some welds that have to be redone, but to access them I have to be able to pull the printed circuit strip out of the wrapper that contains it. I need to know where to unlock to allow the exit as it flows though for a very short ride (less than 1 mm)

デバイス:

Fluke VoltAlert

ステータス:

open

承認済み回答:

541081

編集者: Francesco Taliercio ,

タイトル:

How to extract PCB from chassis of Fluke VoltAlert 1AC-A II?

テキスト:

This is a Fluke VoltAlert 1AC-A II. I have to extract the PCB from the chassis of the same in order to re-heat some components. The circuit moves, but it stops even 1 mm. I tried to see where the block was, but I could not see it. Is there anyone who has already extracted the circuit and knows how?
This is a Fluke VoltAlert 1AC-A II. I have to extract the PCB from the chassis of the same in order to re-heat some components. The circuit moves, but it stops even 1 mm. I tried to see where the block was, but I could not see it. Is there anyone who has already extracted the circuit and knows how?
The acid output from the batteries has corroded some welds that have to be redone, but to access them I have to be able to pull the printed circuit strip out of the wrapper that contains it. I need to know where to unlock to allow the exit as it flows though for a very short ride (less than 1 mm)

デバイス:

Fluke VoltAlert

ステータス:

open

承認済み回答:

541081

編集者: Francesco Taliercio ,

タイトル:

How to extract PCB from chassis of Fluke VoltAlert 1AC-A II?

テキスト:

This is a Fluke VoltAlert 1AC-A II. I have to extract the PCB from the chassis of the same in order to re-heat some components. The circuit moves, but it stops even 1 mm. I tried to see where the block was, but I could not see it. Is there anyone who has already extracted the circuit and knows how? Thank you
The acid output from the batteries has corroded some welds that have to be redone, but to access them I have to be able to pull the printed circuit strip out of the wrapper that contains it. I need to know where to unlock to allow the exit as it flows though for a very short ride (less than 1 mm)
This is a Fluke VoltAlert 1AC-A II. I have to extract the PCB from the chassis of the same in order to re-heat some components. The circuit moves, but it stops even 1 mm. I tried to see where the block was, but I could not see it. Is there anyone who has already extracted the circuit and knows how? Thank you
The acid output from the batteries has corroded some welds that have to be redone, but to access them I have to be able to pull the printed circuit strip out of the wrapper that contains it. I need to know where to unlock to allow the exit as it flows though for a very short ride (less than 1 mm)

デバイス:

Fluke VoltAlert

ステータス:

open

オリジナル投稿者: Francesco Taliercio ,

タイトル:

How to extract PCB from chassis of Fluke VoltAlert 1AC-A II?

テキスト:

This is a Fluke VoltAlert 1AC-A II. I have to extract the PCB from the chassis of the same in order to re-heat some components. The circuit moves, but it stops even 1 mm. I tried to see where the block was, but I could not see it. Is there anyone who has already extracted the circuit and knows how? Thank you

デバイス:

Fluke VoltAlert

ステータス:

open