メインコンテンツにスキップ
ヘルプ

現在のバージョン作成者: jayeff ,

テキスト:

Hi,
Just to give a third option, which is very much like the two above.
Empty the cistern, clean thoroughly around the crack and allow to dry. When dry, lightly sand the crack on both sides using 600 grit sandpaper to roughen the edges so that the sealant will adhere better.
Clean thoroughly after sanding to remove dust etc, then apply [https://www.jbweld.com/products/j-b-weld-twin-tube|this] as per instructions on the pack. Overfill the area so that it can be sanded back. Repeat if necessary.
-Lightly sand for a smooth finish on the outside of the cistern.
+Lightly sand, using 800 Wet and Dry, for a smooth finish on the outside of the cistern.

ステータス:

open

編集者: jayeff ,

テキスト:

Hi,
Just to give a third option, which is very much like the two above.
Empty the cistern, clean thoroughly around the crack and allow to dry. When dry, lightly sand the crack on both sides using 600 grit sandpaper to roughen the edges so that the sealant will adhere better.
Clean thoroughly after sanding to remove dust etc, then apply [https://www.jbweld.com/products/j-b-weld-twin-tube|this] as per instructions on the pack. Overfill the area so that it can be sanded back. Repeat if necessary.
-Sand with the 600 grit and then with this for a [https://www.thesandpaperman.com.au/230-x-280-mm-x-800-grit-norton-t417-tufbak-durite-silicon-carbide-wet-and-dry-waterproof-paper-sheet.html|smooth finish] on the outside of the cistern.
+Lightly sand for a smooth finish on the outside of the cistern.

ステータス:

open

編集者: jayeff ,

テキスト:

Hi,
Just to give a third option, which is very much like the two above.
Empty the cistern, clean thoroughly around the crack and allow to dry. When dry, lightly sand the crack on both sides using 600 grit sandpaper to roughen the edges so that the sealant will adhere better.
Clean thoroughly after sanding to remove dust etc, then apply [https://www.jbweld.com/products/j-b-weld-twin-tube|this] as per instructions on the pack. Overfill the area so that it can be sanded back. Repeat if necessary.
-Sand with the 600 grit and then for a [https://www.thesandpaperman.com.au/230-x-280-mm-x-800-grit-norton-t417-tufbak-durite-silicon-carbide-wet-and-dry-waterproof-paper-sheet.html|smooth finish] on the outside of the cistern.
+Sand with the 600 grit and then with this for a [https://www.thesandpaperman.com.au/230-x-280-mm-x-800-grit-norton-t417-tufbak-durite-silicon-carbide-wet-and-dry-waterproof-paper-sheet.html|smooth finish] on the outside of the cistern.

ステータス:

open

編集者: jayeff ,

テキスト:

Hi,
Just to give a third option, which is very much like the two above.
Empty the cistern, clean thoroughly around the crack and allow to dry. When dry, lightly sand the crack on both sides using 600 grit sandpaper to roughen the edges so that the sealant will adhere better.
Clean thoroughly after sanding to remove dust etc, then apply [https://www.jbweld.com/products/j-b-weld-twin-tube|this] as per instructions on the pack. Overfill the area so that it can be sanded back. Repeat if necessary.
-Sand to a [https://www.thesandpaperman.com.au/230-x-280-mm-x-800-grit-norton-t417-tufbak-durite-silicon-carbide-wet-and-dry-waterproof-paper-sheet.html|smooth finish] on the outside of the cistern.
+
+Sand with the 600 grit and then for a [https://www.thesandpaperman.com.au/230-x-280-mm-x-800-grit-norton-t417-tufbak-durite-silicon-carbide-wet-and-dry-waterproof-paper-sheet.html|smooth finish] on the outside of the cistern.

ステータス:

open

編集者: jayeff ,

テキスト:

Hi,
Just to give a third option, which is very much like the two above.
Empty the cistern, clean thoroughly around the crack and allow to dry. When dry, lightly sand the crack on both sides using 600 grit sandpaper to roughen the edges so that the sealant will adhere better.
Clean thoroughly after sanding to remove dust etc, then apply [https://www.jbweld.com/products/j-b-weld-twin-tube|this] as per instructions on the pack. Overfill the area so that it can be sanded back. Repeat if necessary.
-
-[https://www.thesandpaperman.com.au/230-x-280-mm-x-800-grit-norton-t417-tufbak-durite-silicon-carbide-wet-and-dry-waterproof-paper-sheet.html|Sand] to a smooth finish on the outside of the cistern.
+Sand to a [https://www.thesandpaperman.com.au/230-x-280-mm-x-800-grit-norton-t417-tufbak-durite-silicon-carbide-wet-and-dry-waterproof-paper-sheet.html|smooth finish] on the outside of the cistern.

ステータス:

open

編集者: jayeff ,

テキスト:

Hi,
Just to give a third option, which is very much like the two above.
Empty the cistern, clean thoroughly around the crack and allow to dry. When dry, lightly sand the crack on both sides using 600 grit sandpaper to roughen the edges so that the sealant will adhere better.
Clean thoroughly after sanding to remove dust etc, then apply [https://www.jbweld.com/products/j-b-weld-twin-tube|this] as per instructions on the pack. Overfill the area so that it can be sanded back. Repeat if necessary.
-Sand to a smooth finish on the outside of the cistern.
+[https://www.thesandpaperman.com.au/230-x-280-mm-x-800-grit-norton-t417-tufbak-durite-silicon-carbide-wet-and-dry-waterproof-paper-sheet.html|Sand] to a smooth finish on the outside of the cistern.

ステータス:

open

編集者: jayeff ,

テキスト:

Hi,
Just to give a third option, which is very much like the two above.
Empty the cistern, clean thoroughly around the crack and allow to dry. When dry, lightly sand the crack on both sides using 600 grit sandpaper to roughen the edges so that the sealant will adhere better.
Clean thoroughly after sanding to remove dust etc, then apply [https://www.jbweld.com/products/j-b-weld-twin-tube|this] as per instructions on the pack. Overfill the area so that it can be sanded back. Repeat if necessary.
-Sand to a smooth finish, especially on the outside of the cistern.
+Sand to a smooth finish on the outside of the cistern.

ステータス:

open

編集者: jayeff ,

テキスト:

Hi,
Just to give a third option, which is very much like the two above.
-Empty the cistern and allow to dry. When dry, sand the crack on both sides using 400-600 grit sandpaper to roughen the edges so that the sealant will adhere better.
+Empty the cistern, clean thoroughly around the crack and allow to dry. When dry, lightly sand the crack on both sides using 600 grit sandpaper to roughen the edges so that the sealant will adhere better.
-Clean after sanding to remove dust etc, then apply [https://www.jbweld.com/products/j-b-weld-twin-tube|this] as per instructions on the pack. Overfill the area so that it can be sanded back. Repeat if necessary.
+Clean thoroughly after sanding to remove dust etc, then apply [https://www.jbweld.com/products/j-b-weld-twin-tube|this] as per instructions on the pack. Overfill the area so that it can be sanded back. Repeat if necessary.
Sand to a smooth finish, especially on the outside of the cistern.

ステータス:

open

オリジナル投稿者: jayeff ,

テキスト:

Hi,

Just to give a third option, which is very much like the two above.

Empty the cistern and allow to dry. When dry, sand the crack on both sides using 400-600 grit sandpaper to roughen the edges so that the sealant will adhere better.

Clean after sanding to remove dust etc, then apply [https://www.jbweld.com/products/j-b-weld-twin-tube|this] as per instructions on the pack. Overfill the area so that it can be sanded back. Repeat if necessary.

Sand to a smooth finish, especially on the outside of the cistern.

ステータス:

open