Our problem

The problem is we have tried two different screens on the dudes iPhone and they both work at first but then become unresponsive.

Ok so in thinking maybe some connections are not tight enough. You know the right part of the phone where the cam and sensors and screen connections are? The panel that covers that isn't screwed in tight, how tight is that suppose to be? I lost some screws that keeps the cover on I bave been using different size screws. If that's the problem ig I could order all the screens for the iPhone from amazon. But iv already spent so much money on this guys phone. I ordered a new backplate, I helped him order a new screen. In starting to lose courage I wanted to start helping kids at my school by fixing phones but this one is giving me a bad reputation and its draining my energy I can really spend anymore money. Anyone know the problem can anyone help me out?

⟐ Answered 11月 01, 2019 at 17:55 GMT-7

⟐ Answer accepted 9月 17, 2019 at 4:37 GMT-7

I recently got into a bad car accident, my phone as well. (don't worry, I wasn't texting and driving.) Initially, after I got my phone from my totaled car, it was dead. I got it back up and running with the help of a hair dryer, but I ran into display issues once it booted up. It's got lines in the display where things are being drawn on the screen, and there is obvious damage to the backlight around the top since some areas are brighter than others. Every now and then, the backlight will die completely or be so dim I can't see it in complete darkness. When I use the phone the touchscreen will freak out and open apps I didn't press on. I was planning on replacing the screen, but I'm not sure if it's just the screen or a deeper problem altogether.

Please advise me on what I should do next. Thanks in advance.

Images of screen:

https://imgur.com/a/XcTpQ

⟐ Answer accepted 5月 19, 2019 at 7:33 GMT-7

⟐ Answered 3月 22, 2019 at 22:55 GMT-7

and the volt was 0.01v and with new tristar the battery bracket gived random volts wery fast 3.50v, 2.45v 1.20v etc. Do anybody have any ideas what is going on? Before repair iPhone wasn't charging or warming at all and no powered on. Screen was black and still is. I have reflowed it without any results.

Any help would be much appreciated.

EDIT 01.08.2017

With new good battery and tristar reflowed once again the iPhone works again.

⟐ Commented 9月 15, 2018 at 0:23 GMT-7

will it work or should i ask for a replacement instead? I found two article one said the connector is different, one said the connector of non plus device (6 vs 6s) is different but the 6plus and 6S plus is the same. Also i found that the previous one (non S devices) have both bigger capacity.

Thanks!

⟐ Answered 6月 30, 2018 at 9:04 GMT-7

I'm recently experiencing an issue with my customers iPhone 6 Plus.

The problem is if you go to Settings -> Bluetooth you can only see the Bluetooth heading and instead of the enable/disable toggle switch there's some kind of 'loading' icon. It just keeps spinning forever.

Already restored it, installed latest firmware through iTunes (both normally and through DFU mode), tried reseting network settings alone - none of these would work.

Any clues?

⟐ Answered 4月 14, 2018 at 5:03 GMT-7

⟐ Answered 2月 17, 2018 at 21:40 GMT-7

⟐ Commented 1月 04, 2018 at 13:27 GMT-7

⟐ Answered 5月 08, 2017 at 23:45 GMT-7

⟐ Answered 3月 20, 2017 at 19:19 GMT-7

⟐ Commented 3月 19, 2017 at 11:31 GMT-7

I have toggled airplane mode, took out sim card and cleaned it, reset network settings and finally I erased all settings and content (after a back up) and restored to factory settings. STILL does not have service.

Any Advice?

Thanks friends.

Travis Fox

⟐ Answered 9月 18, 2016 at 21:49 GMT-7

My iPhone 6 Plus was working fine, but had a cracked screen. After replacing the screen using the iFixit kit, the phone is completely dead. It will not power on, reset, or respond to iTunes when plugged into my Macbook. It does get warm when connected to the charger, but that's it. Any suggestions?

-Garland

⟐ Answer edited 4月 20, 2016 at 19:01 GMT-7

Then i came to update my iphone to latest ios and encountered error 53 whilst updating, my phone is now constantly asking to be connected to itunes but always fails with error 53. I've taken the phone apart again and it looks as if i've damaged the home button connector at some point (the original black connector block that connects to the flex cable is completely missing). I'm pretty sure i did this months ago, but somehow managed to reconnect the home cable in such a fashion that the home button function was working but not the finger print sensor.

I was going to buy a new home button, remove the connector and resolder to my original home button cable. Does this sound doable?

⟐ Commented 12月 16, 2015 at 2:29 GMT-7

⟐ Answered 10月 31, 2015 at 3:02 GMT-7

⟐ Answered 2月 02, 2026 at 6:29 GMT-7

⟐ Answered 8月 29, 2022 at 1:56 GMT-7

⟐ Answered 10月 11, 2021 at 22:23 GMT-7

it's the ribbon cable attached to the LCD/Digitizer. Is there any way I can fix it without having to buy another LCD/Digitizer for 90 or so dollars?

Thanks

⟐ Commented 6月 01, 2021 at 3:23 GMT-7