⟐ Answer deleted 4月 03, 2018 at 3:24 GMT-7

i just opened me iPhone 7 to replace the screen. i removed 2 of the tri point y000 screws but the last 2 i can't get to spin. The screws hold down the bracket that protects the battery cable and some other cables.

how do i get them out?

Looking forward to your answers

⟐ Answered 3月 09, 2018 at 15:40 GMT-7

⟐ Answer accepted 1月 16, 2018 at 5:37 GMT-7

I purchased a used iPhone 5 the other week, and a few days later noticed that the screen had started to "touch itself". Initially this was just near the top (it kept dragging down the top menu!). When opening snapchat and using the drawing tool, it was drawing a diagonal line across the screen on its own. Also whilst typing, it would often hold down letters on its own, or the screen would freeze completely!

To get out of the frozen screen, or to stop the screen being touched down on its own I would simply turn the screen off then back on and it would be fine!... for a few secs.

My initial thought was a dodgy digitizer, so I replaced this. It worked fine for half hour then started to resume back to pressing itself!

I tried another screen, and also changed the metal back plate to the scree. Again, this would work fine for a bit then start playing up again!

Despite having 88 days warranty left, Apple wont look at it free as I've removed the screen myself... which apparently voids the warranty.

I'm stuck for ideas!

I've already tried doing a restore! Once from the phone and ones via iTunes.

Stuck for ideas, but it's really annoying! I can't even send a txt properly now without having to turn the screen off then back on a few times to avoid buttons being pressed or it pressing back to the prev screen!?

Any suggestions would be great!

⟐ Answered 1月 11, 2018 at 17:23 GMT-7

Iphone in upright position wont let me type letter Y at all ive tried everything Y doesnt even show up if i slide my finger across the keyboard it just skips it, and the letters underneath it are hard to press, like the first time i try to type letters G,H,V,B (directly underneath Y) it will type the letter closest next to it, but if i touch any of G,H,V,B in the right way i can get the letter i want after a few trys.

if i turn it sideways so Home button is to the right side i have almost no problems, However if i turn it so the home button is to the left side it is hard to type any of the letters on the upper row...

ive tried every keyboard wether its google, text message, notes, ect. they all do the same thing

Any help would be greatly appreciated

---this happend once before a few months ago but went away over night, now it happened this time and has been like this for a week---

⟐ Answered 12月 15, 2017 at 19:33 GMT-7

The problem is sometime i lost signal. I have analize around and found that i have problem with my antenna. When i lost signal all i need to do is squeeze my iphone and the signal will back to normal.

My question is ;

How is bottom antenna work? I heard that iphone 6 use bottom part as the antenna itself but where is the connector. I only found one connector bellow battery connector and then no more so how i can fix network problem on my iphone?

Please dont ask me to reset since i already fix and now that this problem is hardware problem

⟐ Answered 7月 03, 2017 at 13:51 GMT-7

⟐ Answered 3月 15, 2017 at 15:42 GMT-7

⟐ Answered 11月 01, 2016 at 7:51 GMT-7

⟐ Answered 8月 20, 2016 at 20:44 GMT-7

- Thin slender rectangular black rubber piece with slit:

fits to the edge of logic board at the top left where the cables are bent, to protect the cables from any damage from the sharp edge of the logic board. Marked red, on the left of this picture: http://img263.imageshack.us/img263/8572/...

- Very small thin square black rubber piece:

is placed on the cable between the dock connector and the microphone in order to fill up/serve as a spacer, I think in order to isolate the cable from the vibrations/noise caused by the loudspeaker.

http://d3nevzfk7ii3be.cloudfront.net/igi...

- Small thick square black rubber piece:

is stuck on the right open contour of the loudspeaker in order to fill up/serve as a spacer at an empty space next to the rubber microphone inlet, I think to isolate it from any noise interference or vibrations. See: http://s12.postimg.org/440dmyrlo/image.j...

This guy's post helped me find out: Where and how iPhone 4S rubber square piece speaker dropped goes

Either way, it's not a primary element of the iPhone 4 or 4s, so it would probably only cause more wear due to insufficient protection over a long period of time.

Anyone feel free to add any more locations, remarks.

Cheers

⟐ Answered 1月 26, 2015 at 8:55 GMT-7

So i was away the weekend and this happened again and when I tried to charge it up to turn it on again this time it would not power up or find the cable.

So I thought ok as I could still see a lightning bolt cable on the phone showing i need to plug it in, I thought it was just the battery and dock port that went bad.. So i took it apart and ive put in a new battery and put in a new dock port..

Now the screen will not turn on and there is a constant beeping noise when in charge or a vibrate if i switch the slider.. (like the plug in charge noise, bong)

I dont know if i need to put a new screen onto it now.. Hopefully someone can help advise me..

Its weird cause I can see in itunes the phone is connected and is charging now.. but when i try boot the phone up when its not connected to a lighting power cable and when there is no screen attached it will not boot..

I wanted to see if i could hear noises cause i thought i might be able to determine it was the LCD in that case..

Does anyone know if you can boot the phone the up with the screen on it ? as in be able to hear noises etc.

Ive tried the hard resets etc. and even a different power flex cable..

does anyone know about the constant bong noise while on charge???

⟐ Commented 9月 06, 2014 at 14:06 GMT-7

So I redid the whole procedure and it worked without a glitch, for about 3 hours...

Since everything besides the touch-recognition works I think it might be a faulty connection from the digitzier to the logicboard.

Does anybody know which one of the mainboard-connectors is responsible for what task? I named the connectors as follows ;)

• the one on the side of dock-connector (with the black clamp)
• the really annoying small one on the camera-side
• the bigger one on the side of the camera.

Thank you very much for your help!

⟐ Answer accepted 1月 09, 2014 at 22:03 GMT-7

⟐ Answer accepted 9月 23, 2024 at 5:52 GMT-7

service returned not alive with context : is_alive_func returned unhealthy : current fffffffffffc, mask 7fffffffffff, expected 7fffffffffff. SD: 0 BC: 1 Missing sensor(s): TG0B TG0V

service: backboardd,

What do i need to replace in this, it reboot after 2-3 mins but if it is not use i doesnt reboot.

⟐ Answered 3月 20, 2024 at 18:25 GMT-7

⟐ Answered 12月 08, 2021 at 14:25 GMT-7

⟐ Comment deleted 4月 26, 2022 at 20:12 GMT-7

Today I tried reassembling my iPhone 6S after I'd completely tore it down. Now it seems that there is a spare part which I don't know where to place. The part says "160-AF" with an Apple Logo. I also noticed my home button is not working. Could this be the cause of this part? how do I fix it?

⟐ Commented 9月 13, 2021 at 19:12 GMT-7

The strange thing is that Siri works fine, (which uses the earpiece mic),… and normal phone calls work fine which i believe uses the bottom mic.

Voice memos just records static, same as speaker calls for people on the other end listening.

Front facing and Rear facing video all record sound fine..What should i be replacing here?

⟐ Commented 7月 03, 2021 at 5:34 GMT-7

⟐ Edited 2月 18, 2020 at 10:36 GMT-7

⟐ Commented 9月 25, 2019 at 1:35 GMT-7