他に原因など考えられることが有れば教えて下さい　宜しくお願いいたします

背面の材料は用意したが、どうやって交換すればいいか知りたい。

⟐ Answered 4月 01, 2026 at 16:36 GMT-7

⟐ Answered 1月 14, 2026 at 19:35 GMT-7

操作確認すると左下あたりにタッチした部分が波打つ(波紋の様)滲みが出ます。

原因はなにが考えられますか？

本体の曲がりとかでしょうか？

After replacing the screen, crimp the screen with the main body

If you check the operation, the part you touched around the lower left will ripple (like a ripple) ooze.

What can be the cause?

Is it the bend of the main body?

⟐ Commented 12月 24, 2025 at 20:03 GMT-7

ご回答お願いします。

⟐ Answered 11月 06, 2025 at 20:31 GMT-7

⟐ Answered 4月 30, 2025 at 2:50 GMT-7

⟐ Answered 2月 04, 2025 at 2:37 GMT-7

Touch IDを　アクティブ出来ません

これの修理方法を教えていただきたい。

⟐ Answered 9月 16, 2024 at 23:24 GMT-7

Also is there an actual hardware difference in cellular models?. Saw an eSIM setting in a menu not able to access though.. would be fun to try and figure it out..

⟐ Commented 4月 18, 2026 at 21:03 GMT-7

The sound on my iPad all of a sudden stopped working. The sound works fine with headphones in and I can change the volume, but when I unplug the headphones I get absolutely no sound from the speaker, and I can't even change the volume.

I originally thought this must have been a software issue so I went through all the settings, checked mute etc.

After that, I tried a reset using the power and home button, and I even restored to factory settings.

I then changed the speaker with a new one, still no luck.

I have now changed the headphone jack as I thought this may have been interfering, but there is still no sound.

Any help would be very much appreciated!!!

Thanks,

Michael

⟐ Commented 4月 17, 2026 at 17:27 GMT-7

⟐ Answered 4月 16, 2026 at 21:34 GMT-7

I replaced the battery but still getting the TG0B error. The battery level is fluctuating as well. I checked the capacitor C8923 and I got diode resistanc f .883 not sure if this is too high. FL8900 is good as well. What Iam not sure is the Q8900 which for BATT_SWI_FL.

The C8922 which is for BATT_NTC is ok as well it go straight to PMU chip. I tried to jump a wire from the battery terminal directly to batt_ntc n C8922 in case the connection going to the battery is loose but still getting TG0B ... This issue is a pain.

⟐ Answered 4月 15, 2026 at 9:16 GMT-7

Reboots are not spaced evenly at 180s apart, which probably indicates the sensor is responsive at times and not at others? At the beginning of the issue, I could sometimes use it for 5-10 minutes without rebooting, and sometimes less. Charge level fluctuates around 10-20% on each reboot and just randomly when unlocked. The reboots got more frequent and regular over time. Last night it seemed the iPad was charging very slow.

I took it for repair today,

They replaced the battery and the issue persists.

I've read TG0B is an NTC thermistor in the battery.... what could be the next steps? Any possible issues in the measurement circuitry?

panic(cpu 0 caller 0xfffffff0243a0514): userspace watchdog timeout: no successful checkins from thermalmonitord
service returned not alive with context : is_alive_func returned unhealthy : current 1ffffffe, mask 1fffffff, expected 1fffffff. EC: 1 EH: 3758097110 3758097110 SD: 0 BC: 0 RC: -1 BS: 0, Missing sensor(s): TG0B

⟐ Commented 4月 15, 2026 at 9:11 GMT-7

I'm having trouble with my iPad Pro 3rd gen, model A2377. It suddenly stopped charging. I've already replaced both the battery and the charging port, but the issue persists.

It seems to charge very slowly when in DFU mode, but it's not recognized by my computer. I'm really stuck and could use some help.

Has anyone experienced something similar or have any suggestions on what I should try next? Any advice would be greatly appreciated!

⟐ Answered 4月 13, 2026 at 5:44 GMT-7

• Chassis (housing)
• Display
• All 4 speakers
• USB-C charging port

After reassembly, I’m now facing multiple issues:

• Charging is detected but extremely slow (battery percentage barely increases)
• All speakers are heavily distorted (on all corners)
• USB-C audio only works on one side (only one earbud)

The USB-C port is brand new and properly installed.

I double-checked all connections and flex cables, nothing seems out of place.

Has anyone already encountered this kind of issue after a repair like this?

What could be causing it?

I was thinking about something related to power management (PMIC / charging IC or maybe a damaged power line), but I’d like to hear if others have seen similar symptoms.

I got an iPad 9th gen WiFi battery replacement kit. I tried using iopener multiple times as instructed. I even used a blow dryer directed the heat towards the display in a blanket. The display didnt budge at all!

Is it possible to use the adhesive remover that came with the kit and put it along the display? Is there anything i should know about this? like would it ruin the device or the display if i am still unable to open the display?

⟐ Commented 4月 11, 2026 at 13:17 GMT-7

Voltage on the port is 5V, current fluctuates around 0.2A.

Perhaps someone has a diagram of at least previous models to suggest where to look for the problem? Can you advise anything?

Thanks!

⟐ Commented 4月 08, 2026 at 22:45 GMT-7

The battery was full one day and the next morning it wasn't responding to anything. The battery has never actually emptied literally overnight without being used for me (at least not with this ipad). And yet in the morning when I went to turn it on, it's like it wasn't charged for years. It was around 70% charged the night before.

It would not turn on at all, not even the battery logo.

There isn't any visible damage, it didn't fall or something similar. It simply died in the 8 hours when I was asleep for no reason. Didn't move a centimeter. I've never had problems like this with it.

I've tried many different cables and adapters including the original ones and plugging it to my laptop. I let it charge for days at a time with no response.

It's very important to fix it as it's what i use to draw and all my art is on it.

⟐ Commented 4月 07, 2026 at 19:52 GMT-7