⟐ Commented 6月 01, 2026 at 21:29 GMT-7

My grandpa has a Miele w5801 washer, it recently stopped filling water.

It returns a water supply error.

I cleaned the filter at the inlet with little result. I can hear the relays click that are supposed to open the supply solenoid, but no water actually comes in.

Could this be a solenoid issue? If yes, what part number should I look for? Or is there another place I should check first?

Thank you in advance!

⟐ Answered 6月 01, 2026 at 8:13 GMT-7

⟐ Commented 5月 31, 2026 at 7:02 GMT-7

My washer fills up with water but the agitator won't work

⟐ Edited by author 5月 29, 2026 at 14:41 GMT-7

⟐ Commented 5月 29, 2026 at 10:18 GMT-7

⟐ Commented 5月 29, 2026 at 0:59 GMT-7

My washing machine has an issue where it pours water during the spin cycle, while it is draining. Basically, it pours water from the top while draining it out from the bottom. It drains the water faster than it can pour it, so it does not actually fill with water, but it does re-wet the clothes, so the clothes are dripping wet when the cycle is complete.

It also agitates while filling with water. This is not much of a problem, but it started happening the same time that the other issue above started happening.

Model: Kenmore Elite 26964503

This is what the washing machine is supposed to do:

1. Wash Cycle
   1. Fill with water.
   2. When full, begin agitating.
   3. After a while, drain water.
2. Rinse Cycle
   1. Fill with water.
   2. When full, begin agitating.
   3. After a while, drain water.
3. Spin Cycle
   1. Spin while draining water.
   2. When empty, continue spinning and draining.
   3. After a while, stop.

This is what the washing machine actually does (the bold text marks the differences):

1. Wash Cycle
   1. Fill with water while agitating.
   2. When full, continue agitating.
   3. After a while, drain water.
2. Rinse Cycle
   1. Fill with water while agitating.
   2. When full, continue agitating.
   3. After a while, drain water.
3. Spin Cycle
   1. Spin while draining water.
   2. When empty, continue spinning and draining but also begin pouring water from top.
   3. After a while, stop.

The main problem is 3-2: in the spin cycle, the machine begins to pour water after it has drained all of the water. It is not supposed to be pouring water at this point; it defeats the purpose of the spin cycle.

What could this be? What would cause it to pour water during the spin cycle?

⟐ Answered 5月 28, 2026 at 9:47 GMT-7

⟐ Commented 5月 25, 2026 at 8:04 GMT-7

⟐ Commented 5月 24, 2026 at 8:53 GMT-7

⟐ Commented 5月 23, 2026 at 6:59 GMT-7

⟐ Commented 5月 22, 2026 at 2:14 GMT-7

⟐ Commented 5月 18, 2026 at 15:11 GMT-7

⟐ Commented 5月 17, 2026 at 4:49 GMT-7

After a power outage, I wanted to continue the washing cycle. The washing machine would not start. I reset the program by holding the START button for a long time. The washing machine lit up all the LEDs. Then they turned off and nothing happened.

Exactly 20 minutes later, the pump starts running and the LOCK LED begins flashing rapidly, while the RAPID WASH LED flashes a little more slowly. After 5 minutes, the pump stops, but the LED combination keeps flashing in the same way.

There should be two hidden diagnostic LEDs on the inside of the control panel. They are not flashing.

The door lock is working — verified.
The motor works.
The heating element works.
The pressure switch works.
The pump works.

I measured continuity with resistance at the output of the temperature sensor.
The tacho generates voltage according to motor speed when the motor is turning.
The relays on the control board are functional.

Everything was tested outside the washing machine wiring.
The electrolytic capacitors have been replaced.
The triac controlling the door lock is fine and was replaced just in case.

What seems strange, however, is that the door lock engages almost immediately after the washing machine is plugged into the mains. This happens because the processor’s control pin sends a signal to the base of the transistor that triggers the triac.The door lock unlocks only if I unplug the washing machine from the mains.

thank you

⟐ Commented 5月 16, 2026 at 7:16 GMT-7

⟐ Commented 5月 16, 2026 at 1:10 GMT-7

Model : GTW490ACJ6WS

Serial TS973434G

I need know what personality it comes in I got one off fb and I think personality manufacture is off and what ther software is on for test 3,4,5 is on plz

⟐ Edited 5月 16, 2026 at 0:09 GMT-7

⟐ Answer edited 5月 14, 2026 at 2:52 GMT-7