Now.

when i press the power button the power light blinks once and goes off

Tried almost all solutions but nothing worked

solutions please

⟐ Answered 8月 19, 2026 at 12:24 GMT-7

⟐ Answered 8月 19, 2026 at 10:32 GMT-7

⟐ Answered 8月 18, 2026 at 8:06 GMT-7

the necessary steps was taken and yet capcut still crashing why is this occurring

the steps taken is on Windows (PC).

• already cleared the %AppData% cache.
• disabled hardware encoding.
• The crash happens specifically when using Noise Reduction on a blank-screen project or even exporting aac only file to mp4 and aac files.

*

• so need assistance with this thanks

⟐ Commented 8月 18, 2026 at 6:29 GMT-7

⟐ Answer edited 8月 17, 2026 at 12:53 GMT-7

⟐ Answer edited 8月 17, 2026 at 10:15 GMT-7

⟐ Answered 8月 17, 2026 at 5:42 GMT-7

Continued operation of the computer is not recommended by HP and might cause unpredictable behavior that can result in a shutdown, data loss, or computer damage. The computer will shut down in 15 seconds. To prevent the shutdown and continue operation, press the Enter key now.

System Fan (90B)

ENTER-Continue Startup.)

when I turn on my laptop this popup appears.

⟐ Answered 8月 16, 2026 at 13:54 GMT-7

⟐ Answered 8月 16, 2026 at 7:47 GMT-7

⟐ Commented 8月 14, 2026 at 22:21 GMT-7

After days of diagnostic work, having tried 3 different 3rd party aftermarket batteries, here's my conclusion: 3rd party batteries such as BTI batteries are "physically compatible" with the HP Omen X 2S 15-dg0020nr, but they are incompatible at the firmware level. They might work with less demanding laptops, but not with high-wattage dual screen HP Omen X laptops. Here's what I think happens:

• SMBus handshake failure: The BTI/aftermarket controller passes basic detection but fails to properly report real-time telemetry (such as cell temperature or instantaneous wattage draw) back to the laptop's EC.
• Hard shutdowns: When the system switches from AC adapter power to battery power, the EC detects an unsupported or out-of-spec power reading from the aftermarket BTI gas-gauge chip and triggers a hard shutdown within seconds to protect the dual-screen motherboard.

To make matters worse, even if I try to use the laptop with the AC adapter while 3rd party battery is installed, the EC trips the system's BD PROCHOT safety signal because it doesn't recognize the battery as a genuine HP battery, which throttles the CPU clock speed down to 0.8 GHz and locks it there, rendering the laptop so sluggish it becomes practically useless.

If you know a workaround other than buying a genuine HP from eBay (no inventory elsewhere), or having to re-cell the battery (micro-soldering 6 new pouch cells into the old battery pack, a difficult and potentially dangerous task), I would love to hear your thoughts.

⟐ Commented 8月 14, 2026 at 9:40 GMT-7

⟐ Answered 8月 14, 2026 at 8:32 GMT-7

⟐ Answer edited 8月 14, 2026 at 1:54 GMT-7

Issue:

The spacebar key on my HP ZBook Fury has lost its normal tactile feel. It feels mushy, soft, and unresponsive when pressed, especially compared to the surrounding keys. The key still registers input, but the bounce-back and key travel are off.

Questions:

1. Is this issue typically caused by accumulated dust/debris, a misaligned metal stabilizer bar, or a failing rubber dome under the keycap?
2. What is the safest technique to unclip the spacebar keycap on this specific ZBook chassis without snapping the plastic scissor hinges or damaging the wire clips underneath?