＊これは下のアンサーフォーラムページを日本語訳したものです。

Light blinking two times, pause, two times, etc..

⟐ Answer accepted 11月 07, 2022 at 18:06 GMT-7

⟐ Answer accepted 12月 22, 2021 at 18:19 GMT-7

⟐ Answer accepted 7月 14, 2026 at 7:13 GMT-7

⟐ Answer accepted 7月 14, 2026 at 6:55 GMT-7

⟐ Commented 7月 13, 2026 at 5:59 GMT-7

Escutcheon, module, and module cap (untabbed from module but not removed yet due to restrictive wires)

⟐ Commented 7月 12, 2026 at 0:01 GMT-7

I need to open the bottom of my unit so that I can clean or replace the plastic tubing. Does anyone know the type and size of screw for this unit? I've tried all my hex screws, but I apparently don't have the right bit. Thanks.

⟐ Answer accepted 7月 06, 2026 at 16:48 GMT-7

⟐ Commented 7月 06, 2026 at 14:30 GMT-7

⟐ Commented 7月 02, 2026 at 5:55 GMT-7

My DeLonghi ECAM 220.22 Magnifica Start is stuck during startup. The automatic rinse never starts.

The issue started after making a coffee. About 5 minutes later, i smelled something burning. The machine became very hot and the plastic support around the thermoblock slightly melted (i checked it).

Now:

• The machine turns on.
• The brew group moves.
• The lights keep flashing while waiting for the auto rinse.
• No water comes out.

I checked:

• Hoses are clean and not kinked.
• No visible blockage/limescale in the thermoblock.
• Wires/connectors look normal.
• When disconnecting the inlet hose to the thermoblock, only a tiny amount of water comes out (when I power it back on).

Thanks!

⟐ Edited by author 6月 30, 2026 at 14:07 GMT-7

⟐ Answered 6月 27, 2026 at 1:22 GMT-7

⟐ Answered 6月 26, 2026 at 14:18 GMT-7

This is my third machine I’ve received from Keurig support and it’s still happening. I’ve done all the needle cleaning, reseting, descaling, and many other fixes. The unit is not even 3 months old.

I’m just at a loss of what to do because I don’t see many people having the same problem. I’m also sick and tired of wasting perfectly good K Cups! Anybody have ideas how to permanently fix this?

EDIT & SOLUTION: I've been able to resolve the issue using a work around. This is not a fix and I don't know why Keurig hasn't fixed it after years of this happening.

When using a milk based K Cup, press it into the bottom by hand so the K Cup is punctured. Pull it up and rotate 90º and close the lid. This gives the K Cup two holes and much less pressure. It has worked perfectly since I've been doing this.

⟐ Commented 6月 24, 2026 at 3:01 GMT-7

⟐ Edited 6月 23, 2026 at 2:44 GMT-7

I've done this continuity checkup which I found in another post:

"This is usually caused by the heating element rupturing and shorting to the boiler/casing. You can test for this by removing the top/back of the machine (6 small phillips-head screws) and checking for continuity across the heating element contacts (the two 90 degree prongs sticking out of the top of the boiler). If there's no continuity then the boiler needs to be rebuilt with a new heating element and boiler gasket."

The result was .049, which is good I guess. I attached two pictures for you to check if I've tested the right ends.

Anyone know what's the next step to found the problem?

Thank you!

⟐ Answered 6月 18, 2026 at 1:28 GMT-7

Does anyone have an idea how I can disassemble the top section of the Eletta Explore?

I need to replace the standby button.

Thanx

Peter

⟐ Commented 6月 17, 2026 at 14:01 GMT-7

⟐ Commented 6月 13, 2026 at 11:38 GMT-7

⟐ Answer accepted 6月 10, 2026 at 4:16 GMT-7