ケースと液晶パネルとの隙間が無くカッターナイフ等の刃が入りません。

本体は壊れても構いません、液晶が壊れない方法、液晶を別のWatchに使用いたいので、どなたかよい方法が有ったら教えて下さい、お願いします。

How to remove the LCD panel from the ceramiccase of the AppleWatch SE1

There is no gap between the case and the LCD panel, so a blade such as a utility knife cannot fit in.

I don't mind if the main body breaks, but I would like to know if there is a way to avoid breaking the LCD, and I would like to use the LCD on another Watch, so if anyone has a good method please let me know. Thank you.

⟐ Commented 6月 25, 2025 at 19:04 GMT-7

画面をふさぐ前に起動確認したところ、画面が映らなくなってしまいました。iPhoneでBluetooth接続はされてるのが確認出来ます。

買った画面が不良なのか？配線等を気付かないうちに損傷しているのか？

電源が入ってそうな状態でサイドボタン長押しするとバイブレーションも反応してます。

どこがダメなのか？分からないのですが、経験豊富な方で思い当たる事などあれば教えて頂けると幸いです。

⟐ Commented 11月 15, 2024 at 23:17 GMT-7

Apple Watch SEのタッチセンサーを交換しました。中国製のタッチセンサー付きのガラスです。液晶はつかえたので、液晶を外し、そのタッチセンサー付きのガラスに液体紫外線硬化剤を使用して修理しました。

アルミケースや背面を触りながら画面タッチすると操作はできるのですが、画面以外触らず画面のみタッチすると動きません。

この様な症状は何が原因か詳しく知りたいのですが教えていただけますか？

Let me ask you a question first.

I replaced the touch sensor of Apple Watch SE. Glass with touch sensor made in China. I was able to grab the liquid crystal, so I removed the liquid crystal and repaired it using liquid UV hardener on the glass with the touch sensor.

If you touch the screen while touching the aluminum case or the back side, you can operate it, but if you touch only the screen without touching anything other than the screen, it will not work.

I would like to know more about the cause of these symptoms, can you tell me?

⟐ Edited 8月 19, 2023 at 19:44 GMT-7

When I try to pair it with my iPhone 13 (iOS 26), I’m forced to update the watch to watchOS 10.x. The update downloads, but when installation starts I always get the error:

“Unable to verify update. The watchOS update could not be verified because you are not connected to the internet.”

I am definitely connected to the internet and have tried Wi-Fi, mobile data, different networks, resets, and manual pairing without success.

Has anyone experienced this before?

Could this be caused by hardware damage (for example Wi-Fi/Bluetooth corrosion from the earlier water exposure), or is there any known workaround?

⟐ Answered 8月 06, 2025 at 18:17 GMT-7

44 mm SE Watch worked fine but battery run time < 3/4 day with average use and health shows < 80%. Used a heat gun while removing screen for battery replacement. Screen turned a strange bronze color (watch was powered off) after heat applied. After screen was lifted up succesfully attached charger and watch booted up with white bar across screen. Face was lifted up when powered up and not pressed back in. Am I cooked?.

⟐ Commented 6月 07, 2025 at 16:24 GMT-7

⟐ Answer accepted 6月 07, 2025 at 11:02 GMT-7

⟐ Answer accepted 5月 26, 2025 at 5:03 GMT-7

I changed the battery of my Apple Watch SE 40mm. Everything went well until I tested the watch—the touchscreen no longer works. Of course, I checked the flex cables behind the screen, and they are properly connected. Only the tape on the flex cables was damaged. Could this be the cause? thanks a lot

Bonjour tout le monde, j'ai changer la batterie de mon apple watch Se 40mm, tout a bien été jusqu'au moment ou tester la montre, l'ecran tactile ne fonctionne plus, j'ai bien sur verifier les nappes derriere lecran, elles sont bien mises.... il y a que le scotch des nappes qui a été endommager, cela pourrait il venir de ca? je vous remercie

⟐ Edited by author 2月 07, 2025 at 14:57 GMT-7

Thanks to iFixit's guide, I was able to successfully replace the battery in my Apple Watch SE (first gen). I followed all the directions, including those related to battery conditioning after the new one is installed. Having done all that, however—and also having reset my watch to factory settings—the battery is indicating 70% health. I don't know if this means the battery iFixit sent me is itself unhealthy, or if there's something else I need to do for the watch to accurately reflect the new battery's health status. Thoughts?

Thanks

⟐ Answered 1月 26, 2025 at 15:01 GMT-7

What are the paperlike connectors that seem to be a part of the display connector but are next to the 3 ribbon cable connections? Can these be purchased? When I look online for the display cable, it simply only comes with th 3 main connectors and not the 2 outside paperlike connections.

Thanks for your help!

ML

⟐ Commented 7月 14, 2024 at 7:29 GMT-7

⟐ Answered 7月 07, 2024 at 20:17 GMT-7

⟐ Commented 7月 02, 2024 at 9:02 GMT-7

I recently finished repairing my Apple watch SE 42mm watch with a replacement screen straight from IFIXIT. However, now that I've gotten the watch charged, it appears the screen is not allowing me to touch it to use it. I have tried restarting the device, but it still doesn't work. Later on tonight, I will attempt to reset the pairing with my iPhone and update the watchOS on it.

Got any ideas?

Does anyone have any ideas? Please, people I need answers, I'm at a total loss here.

⟐ Commented 5月 21, 2024 at 8:45 GMT-7

Hard reset

Full battery drain/recharge

Factory reset, but now it doesn’t stay on long enough to pair.

Any advice what to try next? Screen works well and can select etc, just not able to stop it from resetting

⟐ Answered 4月 21, 2024 at 10:36 GMT-7

Here is the problem: I did manage to do few successful glass/digitizer replacement, but recently one problem started to appear, the right bottom corrner of display doesnt react to touch. Even if i check the digitizer before instalation, it happends again, and so far happened about 5 times in row.

Im using the LOCA technique as i dont own autoclave.

Im trying to figure out what is the part im messing up, as most likely its my foult, tho few digitizers i bought didnt work properly.

Maybe its worth mentioning that sometimes if a little bubbles appear on LOCA during application i squize them out using very little of pressure around the spot, but i dont think thats the reason for malfunction.

Im kindly asking for any advice!

⟐ Edited by author 4月 16, 2024 at 15:41 GMT-7

⟐ Answered 4月 10, 2024 at 13:50 GMT-7

⟐ Answer edited 4月 10, 2024 at 13:45 GMT-7

what is the connector/antenna for, do I need to replace it.

Then I am also having issues closing it back the screen keeps on popping off, battery is not swollen or anything still has 100% BH and the Watch works fine

I don’t know if this is the Force Touch sensor (The orange like gasket in the above image), I am planning on adding this black rubber glue used for screen replacement T7000 or B8000

⟐ Answered 4月 10, 2024 at 13:30 GMT-7